HardLabs

Active drag system

RocketryVT·active-drag-system·hardware/active-drag-system.kicad_pcb

Active drag system PCB layout, top view — open source RP2040/RP2350 board by RocketryVT

About the Active drag system PCB

Active drag system is an open source RP2040/RP2350 PCB design by RocketryVT, published on GitHub under the MIT license. It is a 4-layer board measuring 33 × 90 mm, with 75 components from 38 distinct parts.

Its main chip is the RP2040, from the RP2040/RP2350 family. Other key parts include the W25Q128JVSIQ, TPS51386RJNR, LD39200PU33R, MMC5983MA and MS560702BA03-50. By type, the board carries 35 capacitors, 20 resistors, 10 ICs, 3 connectors, 2 diodes and 1 crystal.

From the project

Eigen Library, cmake, and arm-none-eabi-gcc tooling required for successful build.

Eigen Library, cmake, and arm-none-eabi-gcc tooling required for successful build.

Note: You must initialize the git submodules prior to utilizing CMake for a proper build.

In the event that your preferred IDE has trouble locating header files and/or is displaying incorrect errors, pass to the first CMake command above. Similarly, if you wish to compile the additional tools (e.g. reading flash, calibrating the IMU, etc.), pass to the first CMake command above as well.

Main components on the Active drag system

RP2040W25Q128JVSIQTPS51386RJNRLD39200PU33RMMC5983MAMS560702BA03-50ADXL375BCCZIIM-42653FODM217ASTP55NF06

Active drag system bill of materials (BOM)

75 components, 38 distinct parts.

QtyPartRefs
1
RP2040
U1
1
W25Q128JVSIQ
U2
1
TPS51386RJNR
U3
1
LD39200PU33R
U4
1
MMC5983MA
U5
1
MS560702BA03-50
U6
1
ADXL375BCCZ
U7
1
IIM-42653
U8
1
FODM217A
U9
1
STP55NF06
U10
1
ABM8AIG-12.000MHZ-12-2Z-T3
X1
1
10118193-0001LF
J3
1
Conn_01x03_Pin
J4
1
Conn_01x04_Pin
J6
2
PMEG3050EP_115
CR1, CR2
1
PTS815 SJM 250 SMTR LFS
SW1
1
WL-SMCW_0603
D1
1
S1G
D2
1
WE-MAIA_4020
L1
15
100nF
C1, C2, C6, C7, C8, C9, C12, C14 +7
Show 18 more
QtyPartRefs
5
2.2uF
C3, C4, C5, C13, C34
2
15pF
C10, C11
5
10uF
C17, C18, C26, C27, C30
4
22uF
C20, C21, C22, C23
1
22pF
C24
2
1uF
C25, C29
1
10nF
C31
1
100
R1
1
200
R2
2
27
R3, R4
4
10k
R5, R6, R14, R15
1
1
R7
2
1k
R8, R9
4
100k
R10, R12, R13, R16
1
150k
R11
2
4.7k
R17, R18
1
1k
R19
1
220
R20

Active drag system design files

The KiCad project lives in the RocketryVT/active-drag-system repository on GitHub; these links point at the commit this page was built from.

Active drag system: common questions

What microcontroller does the Active drag system use?

The Active drag system is built around the RP2040, from the RP2040/RP2350 family.

How big is the Active drag system PCB?

The Active drag system measures 33 × 90 mm, has 4 copper layers and is 1.5422 mm thick.

How many components are on the Active drag system?

75 components, from 38 distinct parts. The full bill of materials is listed on this page.

Where can I download the Active drag system design files?

From the RocketryVT/active-drag-system repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Active drag system design in my own project?

Yes, under the terms of its MIT license, which RocketryVT chose for the repository.

Can I test firmware for the Active drag system without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

More boards in active-drag-system

Similar boards