5 open source boards using the FODM217A
Real designs built with the FODM217A, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
TWIST V1.4
owntech-foundation
100 × 160 mm324 parts6LNo license19OWNVERTER
owntech-foundation
100 × 160 mm355 parts6LNo license12RP2040/RP2350
Active drag system
RocketryVT
33 × 90 mm75 parts4LMIT6TWIST-board
RenewableEnergyNexus
100 × 160 mm325 parts6LNo license1RP2040/RP2350
Drive
MUNAKATA-EPC
62.9 × 77.9 mm55 parts2LNo license0
How designs wire the FODM217A
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the FODM217A connects to, and the resistors, capacitors and other passives placed on it.
- Pin 2 has a resistor to GND on 3 of 5 designs, most often 470 Ω (then 220 Ω).
- Pin 4 has a pull-up to 12V on 3 of 5 designs, most often 12 kΩ (then 1 kΩ).
- Pin 3 is tied to GND on 3 of 5 designs (a signal on 2).
- Pin 1 has a series resistor on 2 of 5 designs, most often 10 kΩ (then 1.4 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: OwnTech_SPIN 40% |
|
| Pin 2 | Connected to: Signal 80% · GND 20% |
|
| Pin 3 | Connected to: GND 60% · a signal 40% |
|
| Pin 4 | Connected to: Signal 80% · VBAT 20% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include TWIST V1.4 by owntech-foundation, OWNVERTER by owntech-foundation, Active drag system by RocketryVT and TWIST-board by RenewableEnergyNexus.
The FODM217A in open source designs
The gallery holds 5 open source boards using the FODM217A from 5 GitHub repositories; a typical one measures about 100 × 160 mm and carries around 324 components.
80% use four copper layers or more, and 20% carry an open source license.
The most starred is TWIST V1.4 by owntech-foundation.
Parts used alongside the FODM217A
Microcontrollers on boards using the FODM217A
What boards using the FODM217A are built for
FODM217A: common questions
Where can I find a FODM217A reference design?
Each of the 5 boards on this page is a real design using the FODM217A. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the FODM217A pin 2?
Pin 2 has a resistor to GND on 3 of 5 designs, most often 470 Ω (then 220 Ω). Counted from the KiCad layouts of 5 open source designs using the FODM217A.
What pull-up resistor is used on the FODM217A pin 4?
Pin 4 has a pull-up to 12V on 3 of 5 designs, most often 12 kΩ (then 1 kΩ). Counted from the KiCad layouts of 5 open source designs using the FODM217A.
How is the FODM217A pin 3 connected?
Pin 3 is tied to GND on 3 of 5 designs (a signal on 2). Counted from the KiCad layouts of 5 open source designs using the FODM217A.
What parts are used alongside the FODM217A?
The AMC1100DUB, AZ1117CH-5.0TRG1, MAX33046EASA+T, MCP6486UT-E/LT and MCP6487T-E/SN appear in the most repositories here.
Which microcontrollers do boards using the FODM217A use?
Most are built on RP2040/RP2350 (2).
How big is a typical board using the FODM217A?
The median is 100 × 160 mm, and 20% are two-layer designs.
What is the most popular open source board using the FODM217A?
By GitHub stars, TWIST V1.4 by owntech-foundation, with 19 stars.
Can I simulate one of these boards using the FODM217A before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.