10 open source boards using the LD39200PU33R
Real designs built with the LD39200PU33R, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Triangulate-ES 01-Watch
sandgum
82.8 × 33 mm125 parts4LNo license22RP2040/RP2350
Active drag system
RocketryVT
33 × 90 mm75 parts4LMIT6ESP32
Hw amp
intentfulmotion
61 × 36 mm47 parts2LCERN-OHL-S-2.06STM32
Harpia FC
gabs911
86 × 56.7 mm62 parts2LNo license5ESP32
URC
spikonado
110 × 90 mm150 parts4LCERN-OHL-W-2.02ESP32
ESP32-S3 6 Motor Driver IMU
Amronos
72.5 × 55 mm92 parts4LNo license2STM32
Robo con for-Wi-Fi
tmcit-ararobo-2026a
86 × 62 mm101 parts4LMIT0STM32
Tulpar Mini FCB
ErdemHtyl
53.5 × 53.5 mm81 parts4LBSD-3-Clause0STM32
IFS08-ES-MainLite
isc-fs
40 × 60 mm75 parts2LNo license0RP2040/RP2350
Active drag system minimal
RocketryVT
33 × 81.8 mm67 parts4LMIT6
How designs wire the LD39200PU33R
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the LD39200PU33R connects to, and the resistors, capacitors and other passives placed on it.
- The OUT pin is tied to 3.3V on 9 of 9 designs.
- The ADJ/SENSE pin is tied to 3.3V on 9 of 9 designs.
- The EN pin has a capacitor to GND on 7 of 9 designs, most often 10 µF (then 100 nF).
- The PG pin is left unconnected on 7 of 9 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUTpin 1 | Connected to: 3.3V 100% | — |
| ADJ/SENSEpin 2 | Connected to: 3.3V 100% | — |
| GNDpin 3, 7 | Connected to: GND 100% | — |
| PGpin 4 | Connected to: Not connected 78% · a signal 22% | — |
| ENpin 5 | Connected to: Signal 56% · 5V 44% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Triangulate-ES 01-Watch by sandgum, Hw amp by intentfulmotion, Active drag system by RocketryVT and Harpia FC by gabs911.
The LD39200PU33R in open source designs
The gallery holds 10 open source boards using the LD39200PU33R from 9 GitHub repositories; a typical one measures about 66.8 × 58.3 mm and carries around 78 components.
70% use four copper layers or more, and 60% carry an open source license.
The most starred is Triangulate-ES 01-Watch by sandgum.
Parts used alongside the LD39200PU33R
Microcontrollers on boards using the LD39200PU33R
What boards using the LD39200PU33R are built for
LD39200PU33R: common questions
Where can I find a LD39200PU33R reference design?
Each of the 10 boards on this page is a real design using the LD39200PU33R. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LD39200PU33R OUT pin connected?
The OUT pin is tied to 3.3V on 9 of 9 designs. Counted from the KiCad layouts of 9 open source designs using the LD39200PU33R.
How is the LD39200PU33R ADJ/SENSE pin connected?
The ADJ/SENSE pin is tied to 3.3V on 9 of 9 designs. Counted from the KiCad layouts of 9 open source designs using the LD39200PU33R.
How is the LD39200PU33R EN pin connected?
The EN pin has a capacitor to GND on 7 of 9 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 9 open source designs using the LD39200PU33R.
Which microcontrollers do boards using the LD39200PU33R use?
Most are built on ESP32 (4), STM32 (4) and RP2040/RP2350 (2).
How big is a typical board using the LD39200PU33R?
The median is 66.8 × 58.3 mm, and 30% are two-layer designs.
What is the most popular open source board using the LD39200PU33R?
By GitHub stars, Triangulate-ES 01-Watch by sandgum, with 22 stars.
Can I simulate one of these boards using the LD39200PU33R before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.