Thermometer
RolandThsive·Thermometer·Electronics/The Main Board/TheMainBoard/TheMainBoard.kicad_pcb
About the Thermometer PCB
Thermometer is an open source ESP32 PCB design by RolandThsive, published on GitHub under the CC-BY-NC-4.0 license. It is a 2-layer board measuring 71.9 × 68.9 mm, with 31 components from 17 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DRV8833PWP, PCA9546APWR, SHT40-AD1B-R3, AS5600 and USBLC6-2SC6. By type, the board carries 11 ICs, 10 resistors, 8 capacitors, 1 transistor and 1 diode.
It belongs with the sensors, robotics & motion and wearables designs in this gallery.
From the project
Part of the AQI Board Project by RolandThsive
This repository is a part of the AQI Board project by @RolandThsive — a wall of analog-style instruments (hygrometer, thermometer, AQI meter and VOC meter) that are as much a showpiece as they are useful.
The Thermometer shows room temperature and dew point with two independent mechanical ticks, each driven by its own N20 motor and tracked by its own absolute encoder.

Main components on the Thermometer
Thermometer bill of materials (BOM)
31 components, 17 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | ~ | 2PinsOut_foot | U1, U12 |
| 1 | DRV8833PWP | IC_DRV8833PWP | U2 |
| 1 | PCA9546APWR | SOP65P640X120-16N | U3 |
| 1 | SHT40-AD1B-R3 | SHT4X | U4 |
| 2 | AS5600 | SOIC8 | U5, U11 |
| 1 | ~ | 4WiresOut_foot | U6 |
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C3-DIP | U7 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U9 |
| 1 | ~ | 5PinsOut_foot | U10 |
| 1 | DMP3007LK3-13 | DMP3007LK313 | Q1 |
| 1 | D_TVS_Filled | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | D1 |
| 3 | 100nF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C3, C4 |
| 2 | 10uF BULK | CP_EIA-3528-21_Kemet-B_HandSolder | C5, C9 |
| 1 | 2.2uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C6 |
| 2 | 0.01uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C7, C8 |
| 8 | 4.7KΩ | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3, R4, R5, R6, R7, R8 |
| 2 | 200mΩ | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R9, R10 |
Thermometer design files
The KiCad project lives in the RolandThsive/Thermometer repository on GitHub; these links point at the commit this page was built from.
Thermometer: common questions
What microcontroller does the Thermometer use?
The Thermometer is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Thermometer PCB?
The Thermometer measures 71.9 × 68.9 mm, has 2 copper layers and is 0.8 mm thick.
How many components are on the Thermometer?
31 components, from 17 distinct parts. The full bill of materials is listed on this page.
Where can I download the Thermometer design files?
From the RolandThsive/Thermometer repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Thermometer design in my own project?
It is published under CC-BY-NC-4.0, which limits how it may be reused; read the license before building on it.
Can I test firmware for the Thermometer without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k