Grupparbete-IoT25S

rt-rtos·Grupparbete-IoT25S·hardware/fg.kicad_pcb

Grupparbete-IoT25S PCB layout, top view — open source ESP32 board by rt-rtos

About the Grupparbete-IoT25S PCB

Grupparbete-IoT25S is an open source ESP32 PCB design by rt-rtos, published on GitHub. It is a 4-layer board measuring 30 × 52.7 mm, with 41 components from 28 distinct parts.

Its main chip is the ESP32-C3-MINI-1, from the ESP32 family. Other key parts include the RT9080-33GJ5, PCF8563T/5,518, USBLC6-2P6 and KH-FG0_5-H2_0-30PIN. By type, the board carries 15 resistors, 14 capacitors, 5 ICs, 2 switches, 2 diodes and 1 crystal.

It belongs with the iot & wireless and displays & leds designs in this gallery.

From the project

Grupparbete för IoT25S Jensen, IoT-arkitektur och datakommunikation.

A 4-layer board for the IoT clock: ESP32-C3-MINI-1, USB-C with input protection, RT9080 3V3 LDO, two RC-debounced buttons, a 30-pin OLED/E-paper FPC connector with an SPI header broken out, and a PCF8563 RTC with coin-cell backup. 30 x 58 mm.

The hardware was a solo side project by Rasmus Tikkanen (@rt-rtos), the project lead - done alongside the group's course scope, which did not include PCB design. The goal was to learn the manufacturing side of PCB design, not to produce a finished board - read the status section before judging the routing.

Main components on the Grupparbete-IoT25S

Grupparbete-IoT25S bill of materials (BOM)

41 components, 28 distinct parts.

QtyPartRefs
1
RT9080-33GJ5
U1
1
PCF8563T/5,518
U2
1
ESP32-C3-MINI-1
U3
1
USBLC6-2P6
U4
1
KH-FG0_5-H2_0-30PIN
U8
1
32K
Seiko Epson
X1
1
USB_C_Receptacle_USB2.0_16P
J1
1
Battery_Cell
BT1
2
SW_Push
SW1, SW2
1
1N4148
D1
1
1N5819WS
D2
1
10u
C1
1
22u
C2
1
1u
C3
1
100n
C4
3
2.2uF
C5, C6, C7
1
4.7uF
C8
1
0.1uF
C9
2
4u7
C10, C11
2
1uF
C12, C13
Show 8 more
QtyPartRefs
1
22pF
C14
2
5.1k
R1, R2
3
10k
R3, R4, R5
2
22
R6, R7
3
100k
R8, R9, R10
2
4.7k
R11, R12
2
4k7
R13, R14
1
1k
R15

Grupparbete-IoT25S design files

The KiCad project lives in the rt-rtos/Grupparbete-IoT25S repository on GitHub; these links point at the commit this page was built from.

Grupparbete-IoT25S: common questions

What microcontroller does the Grupparbete-IoT25S use?

The Grupparbete-IoT25S is built around the ESP32-C3-MINI-1, from the ESP32 family.

How big is the Grupparbete-IoT25S PCB?

The Grupparbete-IoT25S measures 30 × 52.7 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Grupparbete-IoT25S?

41 components, from 28 distinct parts. The full bill of materials is listed on this page.

Where can I download the Grupparbete-IoT25S design files?

From the rt-rtos/Grupparbete-IoT25S repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Grupparbete-IoT25S design in my own project?

The repository has no license, so all rights stay with rt-rtos. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Grupparbete-IoT25S without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards