ESP32-Flight-Controller v2

shazmeenShz·ESP32-Flight-Controller-v2·KiCad/flight_controller_rev2.kicad_pcb

ESP32-Flight-Controller v2 PCB layout, top view — open source ESP32 board by shazmeenShz

About the ESP32-Flight-Controller v2 PCB

ESP32-Flight-Controller v2 is an open source ESP32 PCB design by shazmeenShz, published on GitHub under the MIT license. It is a 4-layer board measuring 67.5 × 53.5 mm, with 61 components from 44 distinct parts.

Its main chip is the ESP32-WROOM-32E, from the ESP32 family. Other key parts include the AMS1117-3.3, CH340C, MPU-6050, USBLC6-2SC6 and MP1584EN. By type, the board carries 21 capacitors, 17 resistors, 6 ICs, 6 connectors, 5 diodes and 2 switches.

It belongs with the robotics & motion, iot & wireless and power & battery designs in this gallery.

From the project

The manufactured revision of a 4-layer ESP32 flight-controller PCB, designed in KiCad 8.

The manufactured revision of a 4-layer ESP32 flight-controller PCB, designed in KiCad 8.

The board is built around an ESP32-WROOM-32E. It takes a LiPo on an XT30, makes 5 V with an MP1584 and 3.3 V with an AMS1117, and brings out USB-C programming, an MPU-6050, GPS, and receiver headers. This directory is the Rev 2 hardware only: schematic, PCB, Gerbers, BOM, and photos. There is no flight firmware here.

ESP32-Flight-Controller v2, from the project README
From the project README

Main components on the ESP32-Flight-Controller v2

ESP32-Flight-Controller v2 bill of materials (BOM)

61 components, 44 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-WROOM-32E
U1
1
AMS1117-3.3
U2
1
CH340C
U3
1
MPU-6050
U4
1
USBLC6-2SC6
U5
1
MP1584EN
U6
1
2N3904
Q1
1
Battery XT30
J1
1
IBUS/SBUS RECIEVER
J3
1
PWM RECIEVER
J4
1
MOTOR OUT
J5
1
GPS
J6
1
USB_C_RECEPTACLE_USB2.0_16P
USB_C_Receptacle_USB2.0_16P
J9
1
Buzzer
BZ1
1
500MA
500mA
F1
1
RESET
SW1
1
BOOT
SW2
1
SS34
D1
1
WS2812B
D2
1
1N4148
D3
Show 24 more
QtyPartRefs
1
SM6T24A
D4
1
D_Schottky
D5
1
22U
22u
L1
1
100uF 35V
C1
12
100NF
100nF
C2, C5, C6, C7, C8, C9, C12, C13 +4
1
100uF 16V
C3
1
10uF 16V
C4
1
2.2NF
2.2nF
C10
1
10NF
10nF
C11
1
22UF
22uF
C14
1
220P
220p
C18
2
10UF
10uF
C19, C21
1
22K
22k
R1
2
100K
100k
R2, R3
2
10K
10k
R4, R5
1
1k
R6
1
330K
330k
R7
2
5.1K
5.1k
R8, R9
2
4.7K
4.7k
R10, R11
2
22
R12, R13
1
200K
200k
R14
1
211K
211k
R15
1
40.2K
40.2k
R16
1
68.1K
68.1k
R17

ESP32-Flight-Controller v2 design files

The KiCad project lives in the shazmeenShz/ESP32-Flight-Controller-v2 repository on GitHub; these links point at the commit this page was built from.

ESP32-Flight-Controller v2: common questions

What microcontroller does the ESP32-Flight-Controller v2 use?

The ESP32-Flight-Controller v2 is built around the ESP32-WROOM-32E, from the ESP32 family.

How big is the ESP32-Flight-Controller v2 PCB?

The ESP32-Flight-Controller v2 measures 67.5 × 53.5 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the ESP32-Flight-Controller v2?

61 components, from 44 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the ESP32-Flight-Controller v2 design files?

From the shazmeenShz/ESP32-Flight-Controller-v2 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the ESP32-Flight-Controller v2 design in my own project?

Yes, under the terms of its MIT license, which shazmeenShz chose for the repository.

Can I test firmware for the ESP32-Flight-Controller v2 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards