Cyd obd adapter
ssjrocks·cyd-obd-adapter·hardware/cyd-obd-adapter.kicad_pcb
About the Cyd obd adapter PCB
Cyd obd adapter is an open source ESP32 PCB design by ssjrocks, published on GitHub under the AGPL-3.0 license. It is a 4-layer board measuring 100 × 60 mm, with 166 components from 51 distinct parts.
Its main chip is the ESP32-WROVER-E-N8R8, from the ESP32 family. Other key parts include the LMR36510ADDAR, TLV62569DBVR, AP2112K-3.3TRG1, CH340C and TJA1042T/3. By type, the board carries 74 resistors, 38 capacitors, 15 ICs, 15 diodes, 8 relays and 5 transistors.
It belongs with the iot & wireless and power & battery designs in this gallery.
From the project
Open low-level OBD-II adapter: ESP32 with HS-CAN, single-wire CAN, flex CAN, 2x K-line, L-line and pin voltage probes, exposed over BT Classic, BLE, WiFi and USB as a raw proxy. KiCad 10, JLCPCB-ready.
An open, low-level OBD-II adapter: an ESP32 with every bus a car's diagnostic port uses, exposed over Bluetooth Classic, BLE, WiFi and USB as a raw proxy. Another device (phone, laptop, the cyd-vehicle-dash screen) sends raw CAN frames and K-line bytes; the adapter puts them on whichever pins the selected car profile uses.
Designed around a 2005 Holden/Opel Astra H, where a cheap ELM327 only reaches the engine ECU: the instrument cluster and body modules sit on single-wire CAN (pin 1) and the gearbox possibly on another line.

Main components on the Cyd obd adapter
Cyd obd adapter bill of materials (BOM)
166 components, 51 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LMR36510ADDAR | Texas_HTSOP-8-1EP_3.9x4.9mm_P1.27mm_EP2.95x4.9mm_Mask2.4x3.1mm_ThermalVias | U1 |
| 1 | TLV62569DBVR | SOT-23-5 | U2 |
| 1 | ESP32-WROVER-E-N8R8 | ESP32-WROVER-E | U3 |
| 1 | AP2112K-3.3TRG1 | SOT-23-5 | U4 |
| 1 | CH340C | SOIC-16_3.9x9.9mm_P1.27mm | U5 |
| 2 | TJA1042T/3 | SOIC-8_3.9x4.9mm_P1.27mm | U6, U8 |
| 2 | MCP2518FDT-E/SL | SOIC-14_3.9x8.7mm_P1.27mm | U7, U9 |
| 1 | NCV7356D1R2G | SOIC-8_3.9x4.9mm_P1.27mm | U10 |
| 2 | TJA1021T/20 | SOIC-8_3.9x4.9mm_P1.27mm | U11, U12 |
| 1 | TCA9555PWR | TSSOP-24_4.4x7.8mm_P0.65mm | U13 |
| 2 | ADS7828E/2K5 | TSSOP-16_4.4x5mm_P0.65mm | U14, U15 |
| 2 | MMBT3904 | SOT-23 | Q1, Q2 |
| 3 | 2N7002 | SOT-23 | Q3, Q4, Q5 |
| 2 | 40MHZ 40MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1, Y2 |
| 1 | C165948 USB-C | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | AUX | PinHeader_1x05_P2.54mm_Vertical | J2 |
| 1 | OBD-FMB-16-SN-B-E-R-V2 | OBD2_Male_Antenk_OBD-FMB-16_SMD | J3 |
| 1 | 0.75A/33V | Fuse_1812_4532Metric | F1 |
| 8 | AQY282SX | SO-4_4.4x3.6mm_P2.54mm | K1, K2, K3, K4, K5, K6, K7, K8 |
| 1 | C318884 RESET | SW_Push_1P1T_XKB_TS-1187A | SW1 |
Show 31 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | C318884 BOOT | SW_Push_1P1T_XKB_TS-1187A | SW2 |
| 1 | SMBJ26A | D_SMB | D1 |
| 1 | SS210 | D_SMA | D2 |
| 2 | SS14 | D_SMA | D3, D4 |
| 1 | C2286 red | LED_0603_1608Metric | D5 |
| 7 | NUP2105L | SOT-23 | D6, D10, D11, D12, D13, D14, D15 |
| 3 | 1N4148WS | D_SOD-323 | D7, D8, D9 |
| 1 | 22UH 22uH | L_Sunlord_SWPA6045S | L1 |
| 1 | 2.2UH 2.2uH | L_Sunlord_SWPA3015S | L2 |
| 1 | 47UH 47uH | L_1210_3225Metric | L3 |
| 2 | C50254 2.2uF 50V | C_1206_3216Metric | C1, C2 |
| 17 | 100NF 100nF | C_0603_1608Metric | C3, C5, C12, C14, C18, C19, C20, C21 +9 |
| 6 | 1UF 1uF | C_0603_1608Metric | C4, C15, C16, C17, C36, C38 |
| 4 | C12891 22uF 25V | C_1206_3216Metric | C6, C7, C10, C11 |
| 3 | C15850 10uF 25V | C_0805_2012Metric | C8, C9, C13 |
| 4 | 22PF 22pF | C_0603_1608Metric | C22, C23, C27, C28 |
| 2 | 100PF 100pF | C_0603_1608Metric | C30, C31 |
| 22 | 100K 100k | R_0603_1608Metric | R1, R3, R6, R30, R32, R34, R43, R45 +14 |
| 1 | 24K 24k | R_0603_1608Metric | R2 |
| 1 | 22K 22k | R_0603_1608Metric | R4 |
| 1 | 470K 470k | R_0603_1608Metric | R5 |
| 8 | 10K 10k | R_0603_1608Metric | R7, R8, R9, R10, R11, R12, R22, R23 |
| 6 | 4.7K 4.7k | R_0603_1608Metric | R13, R14, R15, R16, R20, R21 |
| 2 | 1k | R_0603_1608Metric | R17, R28 |
| 2 | 5.1K 5.1k | R_0603_1608Metric | R18, R19 |
| 2 | 120 | R_0805_2012Metric | R24, R25 |
| 1 | 2.7K 2.7k | R_0603_1608Metric | R26 |
| 1 | 6.49K 6.49k | R_0603_1608Metric | R27 |
| 3 | C36171 510 1W | R_2512_6332Metric | R29, R31, R33 |
| 8 | 390 | R_0603_1608Metric | R35, R36, R37, R38, R39, R40, R41, R42 |
| 16 | 20K 20k | R_0603_1608Metric | R44, R46, R48, R50, R52, R54, R56, R58 +8 |
Cyd obd adapter design files
The KiCad project lives in the ssjrocks/cyd-obd-adapter repository on GitHub; these links point at the commit this page was built from.
Cyd obd adapter: common questions
What microcontroller does the Cyd obd adapter use?
The Cyd obd adapter is built around the ESP32-WROVER-E-N8R8, from the ESP32 family.
How big is the Cyd obd adapter PCB?
The Cyd obd adapter measures 100 × 60 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Cyd obd adapter?
166 components, from 51 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Cyd obd adapter design files?
From the ssjrocks/cyd-obd-adapter repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Cyd obd adapter design in my own project?
Yes, under the terms of its AGPL-3.0 license, which ssjrocks chose for the repository.
Can I test firmware for the Cyd obd adapter without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k