MIDIController

stefanhepp·eOrgan·boards/MIDIController/MIDIController.kicad_pcb

MIDIController PCB layout, top view — open source NXP board by stefanhepp

About the MIDIController PCB

MIDIController is an open source NXP PCB design by stefanhepp, published on GitHub under the CC-BY-SA-4.0 license. It is a 2-layer board measuring 150 × 100 mm, with 35 components from 23 distinct parts.

Its main chip is the Teensy4.1, from the NXP family. By type, the board carries 14 connectors, 9 capacitors, 9 resistors, 1 IC, 1 battery holder and 1 diode.

It belongs with the audio and displays & leds designs in this gallery.

From the project

Electronic organ console project.

This project contains various parts of a midi-organ. The project consists of four main parts:

- The Pedalboard: a 29 note midi foot pedal, mostly ARGO compliant. This odd number of notes was choosen because of size restrictions (I wanted it to fit under my e-piano). - The organ console: contains stops, a lcd display, and all connectors and hardware to wire it to a PC. Up to three midi keyboards can be used as input devices, as well as the midi pedalboard. - The organ desk: a framework for all the parts, contains speakers and some additional foot-stops. This is also designed to hold the PC. -…

Main components on the MIDIController

MIDIController bill of materials (BOM)

35 components, 23 distinct parts.

QtyPartRefs
1
Teensy4.1
U1
1
Bat
J1
1
MIDICon
J2
1
IO_Boards
J3
1
USB_A
J4
1
I2S1
J5
1
I2S2
J6
1
Raspberry_Pi_2_3
J7
1
RPI_Pwr
J8
1
Eth
J9
1
RJ45_Bel_SI-60062-F_fixed
J10
1
USB
J11
1
LineIn
J12
1
LineOut
J13
1
Conn_02x05_Odd_Even
J14
1
Battery_Cell
BT1
1
LED
D1
2
100nF
C1, C3
1
10uF
C2
6
10nF
C4, C5, C6, C7, C8, C9
Show 3 more
QtyPartRefs
2
4k7
R1, R2
6
100
R3, R4, R5, R6, R7, R8
1
470
R9

MIDIController design files

The KiCad project lives in the stefanhepp/eOrgan repository on GitHub; these links point at the commit this page was built from.

MIDIController: common questions

What microcontroller does the MIDIController use?

The MIDIController is built around the Teensy4.1, from the NXP family.

How big is the MIDIController PCB?

The MIDIController measures 150 × 100 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the MIDIController?

35 components, from 23 distinct parts. The full bill of materials is listed on this page.

Where can I download the MIDIController design files?

From the stefanhepp/eOrgan repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the MIDIController design in my own project?

Yes, under the terms of its CC-BY-SA-4.0 license, which stefanhepp chose for the repository.

Can I test firmware for the MIDIController without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug NXP firmware against it before you order a PCB.

More boards in eOrgan

Similar boards