Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation

subbuu-aadhii·Simulation-Based-Adaptive-Extended-Kalman-Filter-for-UAV-State-Estimation·PCB_Design/KiCad_Project/UAV_Flight_Controller.kicad_pcb

Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation PCB layout, top view — open source ESP32 board by subbuu-aadhii

About the Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation PCB

Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation is an open source ESP32 PCB design by subbuu-aadhii, published on GitHub under the MIT license. It is a 4-layer board measuring 100 × 100 mm, with 69 components from 37 distinct parts.

Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the DRV8212P, AP63203WU, USBLC6-2SC6, MPU-6050 and BMP280. By type, the board carries 27 capacitors, 12 resistors, 9 ICs, 8 connectors, 4 diodes and 3 switches.

It belongs with the robotics & motion and sensors designs in this gallery.

From the project

A simulation-based implementation of an AEKF for robust UAV state estimation under realistic sensor degradation conditions.

Modern UAVs rely heavily on onboard sensors such as IMUs and barometric pressure sensors for navigation and control. Unfortunately, these sensors are affected by

- Gaussian sensor noise - Wind-induced oscillations - Sudden disturbances (gusts) - Thermal drift - Time-varying environmental conditions

Traditional Kalman Filters assume constant measurement noise and therefore degrade in performance when operating under dynamic environments.

Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation, from the project README
From the project README

Main components on the Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation

Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation bill of materials (BOM)

69 components, 37 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-S3-WROOM-1
U1
4
DRV8212P
U2, U3, U4, U5
1
AP63203WU
U6
1
USBLC6-2SC6
U7
1
MPU-6050
U8
1
BMP280
U9
2
AON6411
Q1, Q2
1
USB_C
J1
1
MOTOR1-4
Motor1
J2
1
MOTOR1-4
Motor2
J3
1
MOTOR1-4
Motor3
J4
1
MOTOR1-4
Motor4
J5
1
ESC_Header
J6
1
I2C_Header
J7
1
UART_Header
J8
2
18650_Cell
BT1, BT2
1
15A
F1
1
Power
SW1
1
Reset
SW2
1
Boot
SW3
Show 17 more
QtyPartRefs
2
SS34
D1, D2
1
SMAJ9.0CA
D3
1
LED
D4
1
3.9uH
L1
15
100nF
C1, C3, C8, C9, C11, C13, C14, C15 +7
6
10uF
C2, C7, C16, C19, C22, C25
2
22uF
C4, C5
1
1uF
C6
1
2.2nF
C10
1
10nF
C12
1
470uF
C27
3
100k
R1, R2, R8
1
33k
R3
2
5.1k
R4, R5
3
10k
R6, R7, R12
1
1k
R9
2
4.7k
R10, R11

Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation design files

The KiCad project lives in the subbuu-aadhii/Simulation-Based-Adaptive-Extended-Kalman-Filter-for-UAV-State-Estimation repository on GitHub; these links point at the commit this page was built from.

Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation: common questions

What microcontroller does the Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation use?

The Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation is built around the ESP32-S3-WROOM-1, from the ESP32 family.

How big is the Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation PCB?

The Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation measures 100 × 100 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation?

69 components, from 37 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation design files?

From the subbuu-aadhii/Simulation-Based-Adaptive-Extended-Kalman-Filter-for-UAV-State-Estimation repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation design in my own project?

Yes, under the terms of its MIT license, which subbuu-aadhii chose for the repository.

Can I test firmware for the Simulation-Based-Adaptive-Extended-Kalman-Filter for-UAV-State-Estimation without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards