MiniMP3
syntonos·miniMP3·PCB/mp3.kicad_pcb
About the MiniMP3 PCB
MiniMP3 is an open source ESP32 PCB design by syntonos, published on GitHub. It is a 4-layer board measuring 54.3 × 27 mm, with 24 components from 16 distinct parts.
Its main chip is the ESP32-WROOM-32E, from the ESP32 family. Other key parts include the MAX98357A, TPA6132A2RTE, NCP1117-3.3_TO252 and CH340X. By type, the board carries 10 capacitors, 6 ICs, 4 resistors, 2 switches and 1 connector.
It belongs with the iot & wireless, displays & leds and power & battery designs in this gallery.
From the project
Really more of a fun PCB tiling exercise than anything.
Really more of a fun PCB tiling exercise than anything.
Plug in the LiPo Battery (JST-PH 2.0mm).
Insert the heat-sets into the two slots above and below.
Flash firmware through USB-C, and a platform like Arduino IDE. Hold the boot button, flick the power switch on and off, select the right USB connection, and upload the firmware.
(Firmware currently in testing, will be in release notes when fully finished.)

Main components on the MiniMP3
MiniMP3 bill of materials (BOM)
24 components, 16 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-WROOM-32E | ESP32-WROOM-32E | U1 |
| 2 | MAX98357A | TQFN-16-1EP_3x3mm_P0.5mm_EP1.23x1.23mm | U3, U5 |
| 1 | TPA6132A2RTE | WQFN-16-1EP_3x3mm_P0.5mm_EP1.6x1.6mm_ThermalVias | U4 |
| 1 | NCP1117-3.3_TO252 | TO-252-2 | U6 |
| 1 | CH340X | MSOP-10_3x3mm_P0.5mm | U7 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB-C_16 | J2 |
| 1 | USBLC6-2SC6 | SOT-23-6 | ESD1 |
| 2 | ~ | XUNPU QS-302-AGS8P | SW1, SW2 |
| 1 | 2.2uF | C_0603_1608Metric | C3 |
| 4 | 1uF | C_0603_1608Metric | C4, C5, C7, C8 |
| 2 | 0.1uF | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C6, C9 |
| 1 | 22uF | C_0603_1608Metric | C10 |
| 2 | 0.1uF | C_0603_1608Metric | C11, C12 |
| 2 | 5.1k | R_0603_1608Metric | R1, R2 |
| 1 | 4.7k | R_0603_1608Metric | R3 |
| 1 | 10k | R_0603_1608Metric | R4 |
MiniMP3 design files
The KiCad project lives in the syntonos/miniMP3 repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/mp3.kicad_pcb
- SchematicPCB/mp3.kicad_sch
MiniMP3: common questions
What microcontroller does the MiniMP3 use?
The MiniMP3 is built around the ESP32-WROOM-32E, from the ESP32 family.
How big is the MiniMP3 PCB?
The MiniMP3 measures 54.3 × 27 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the MiniMP3?
24 components, from 16 distinct parts. The full bill of materials is listed on this page.
Where can I download the MiniMP3 design files?
From the syntonos/miniMP3 repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the MiniMP3 design in my own project?
The repository has no license, so all rights stay with syntonos. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the MiniMP3 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k