24 open source boards using the CH340X

Real designs built with the CH340X, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

24 boardsClear filters|Most starred

How designs wire the CH340X

Read from the KiCad layouts of 19 open source designs, one per repository: what each pin of the CH340X connects to, and the resistors, capacitors and other passives placed on it.

  • The V3 pin has a capacitor to GND on 17 of 18 designs, most often 100 nF (then 10 nF).
  • The VCC pin has a decoupling capacitor on 14 of 18 designs, most often 100 nF (then 10 µF).
  • The CTS pin is left unconnected on 14 of 19 designs (a signal on 4).
GNDpin 3Connected to: GND 89%
CTSpin 5Connected to: Not connected 74% · a signal 21%
TNOW/DTRpin 6Connected to: Signal 61% · not connected 39%
  • Resistor to GND on 33% · 4.7 kΩ (5), 5.1 kΩ (1)
  • Series resistor on 33% · 10 kΩ (3), 22 kΩ (1), 5.1 kΩ (1)
VCCpin 7Connected to: 5V 89%
  • Decoupling capacitor on 78% · 100 nF (14), 10 µF (2), 330 nF (2)
V3pin 10Connected to: Signal 56% · 3.3V 44%
  • Capacitor to GND on 94% · 100 nF (14), 10 nF (2), 10 µF (1)

5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MiniSpeedCam-1.2 by Valar-Systems, ZXEVO.1010 by UzixLS, GammaSpectrometer by RobertGawron and ProcessingAndStorage by RobertGawron.

The CH340X in open source designs

The gallery holds 24 open source boards using the CH340X from 19 GitHub repositories; a typical one measures about 57 × 50 mm and carries around 54 components.

54% are two-layer designs, the rest use four layers or more, and 42% carry an open source license.

The most starred is MiniSpeedCam-1.2 by Valar-Systems.

Microcontrollers on boards using the CH340X

CH340X: common questions

Where can I find a CH340X reference design?

Each of the 24 boards on this page is a real design using the CH340X. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the CH340X V3 pin connected?

The V3 pin has a capacitor to GND on 17 of 18 designs, most often 100 nF (then 10 nF). Counted from the KiCad layouts of 19 open source designs using the CH340X.

What decoupling capacitors do designs use on the CH340X VCC pin?

The VCC pin has a decoupling capacitor on 14 of 18 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 19 open source designs using the CH340X.

How is the CH340X CTS pin connected?

The CTS pin is left unconnected on 14 of 19 designs (a signal on 4). Counted from the KiCad layouts of 19 open source designs using the CH340X.

What parts are used alongside the CH340X?

The AP2112K-3.3, ESP32-WROOM-32E, STM32G070KBTX and TP4056 appear in the most repositories here.

Which microcontrollers do boards using the CH340X use?

Most are built on STM32 (9), ESP32 (7), AVR/Arduino (2) and FPGA (1).

How big is a typical board using the CH340X?

The median is 57 × 50 mm, and 54% are two-layer designs.

What is the most popular open source board using the CH340X?

By GitHub stars, MiniSpeedCam-1.2 by Valar-Systems, with 112 stars.

Can I simulate one of these boards using the CH340X before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part