Greenhouse controller

taseraul·greenhouse-controller·hardware/hardware.kicad_pcb

Greenhouse controller PCB layout, top view — open source ESP8266 board by taseraul

About the Greenhouse controller PCB

Greenhouse controller is an open source ESP8266 PCB design by taseraul, published on GitHub. It is a 2-layer board measuring 81 × 67 mm, with 77 components from 43 distinct parts.

Its main chip is the ESP-12F, from the ESP8266 family. Other key parts include the MP2451DT-LF-Z, TP4054, ATTINY45-20SU, HT75XX-1-SOT89 and POLOLU_BREAKOUT_A4988. By type, the board carries 25 resistors, 13 capacitors, 9 diodes, 5 ICs, 5 transistors and 5 connectors.

Main components on the Greenhouse controller

Greenhouse controller bill of materials (BOM)

77 components, 43 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
MP2451DT-LF-Z
IC1
1
TP4054
IC2
1
ATTINY45-20SU
ATtiny45-20SU
U1
1
ESP-12F
U2
1
HT75XX-1-SOT89
HT75xx-1-SOT89
U3
1
POLOLU_BREAKOUT_A4988
Pololu_Breakout_A4988
A1
3
2N7002
Q1, Q3, Q5
2
SI2319CDS
Si2319CDS
Q2, Q4
1
USB_B_Micro
J1
1
CONN_02X03_ODD_EVEN
Conn_02x03_Odd_Even
J2
1
Barrel_Jack_Switch
J3
1
CONN_01X02
Conn_01x02
J4
1
CONN_01X02
Conn_01x02
J5
3
CONN_01X03
Conn_01x03
Analog2, Analog3, TEMP1
1
4 x AA(A)
BT1
1
18650
BT2
4
SW_Push
FLASH1, PB1, PB2, RESET1
1
ADW1103HLW
K1
1
CONN_02X03
Conn_02x03
Microstep1
2
CONN_01X04
Conn_01x04
PROG1, StepperMotor1
Show 23 more
QtyPartRefs
5
D_Schottky
D1, D4, D5, D6, D7
1
GREEN
D2
1
RED
D3
1
ORANGE
D8
1
BLUE
D9
1
3.3U
3.3u
L1
7
10U/6.3V
10u/6.3V
C1, C5, C6, C9, C10, C11, C13
1
33P
33p
C2
1
100N
100n
C3
1
4.7U/36V
4.7u/36V
C4
1
100U/36V
100u/36V
C7
1
10U/36V
10u/36V
C8
1
10U/10V
10u/10V
C12
1
33K
33k
R1
7
10K
10k
R2, R7, R8, R11, R15, R18, R21
1
100K
100k
R3
1
47K
47k
R4
3
4.7K
4.7k
R5, R6, R12
5
0
R9, R22, R23, R24, R25
1
300K
300k
R10
3
1k
R13, R19, R20
2
4.3
R14, R17
1
1.6k - 1.8k
R16

Greenhouse controller design files

The KiCad project lives in the taseraul/greenhouse-controller repository on GitHub; these links point at the commit this page was built from.

Greenhouse controller: common questions

What microcontroller does the Greenhouse controller use?

The Greenhouse controller is built around the ESP-12F, from the ESP8266 family.

How big is the Greenhouse controller PCB?

The Greenhouse controller measures 81 × 67 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Greenhouse controller?

77 components, from 43 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Greenhouse controller design files?

From the taseraul/greenhouse-controller repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the Greenhouse controller design in my own project?

The repository has no license, so all rights stay with taseraul. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Greenhouse controller without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP8266 firmware against it before you order a PCB.

Similar boards