13 open source boards using the ATtiny45-20SU

Real designs built with the ATtiny45-20SU, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

13 boardsClear filters|Most starred

How designs wire the ATtiny45-20SU

Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the ATtiny45-20SU connects to, and the resistors, capacitors and other passives placed on it.

  • The VCC pin has a decoupling capacitor on 10 of 12 designs, most often 100 nF (then 10 µF).
  • The XTAL2/PB4 pin has a series resistor on 6 of 13 designs, most often 470 Ω (then 5.6 kΩ).
  • The AREF/PB0 pin has a series resistor on 6 of 13 designs, most often 22 Ω (then 560 Ω).
  • The PB1 pin has a series resistor on 6 of 13 designs, most often 470 Ω (then 1 kΩ).
XTAL1/PB3pin 2Connected to: A connector 31%
  • Series resistor on 38% · 470 Ω (2), 220 Ω (1), 0 Ω (1)
XTAL2/PB4pin 3Connected to: A connector 31% · not connected 23%
  • Series resistor on 46% · 470 Ω (2), 5.6 kΩ (1), 1 kΩ (1)
GNDpin 4Connected to: GND 92%
AREF/PB0pin 5Connected to: A connector 85%
  • Series resistor on 46% · 22 Ω (1), 560 Ω (1), 1.5 kΩ (1)
PB1pin 6Connected to: A connector 77%
  • Series resistor on 46% · 470 Ω (1), 1 kΩ (1), 560 Ω (1)
PB2pin 7Connected to: A connector 83%
  • Series resistor on 33% · 22 Ω (1), 1.5 kΩ (1), 220 Ω (1)
VCCpin 8Connected to: 3.3V 92%
  • Decoupling capacitor on 83% · 100 nF (6), 10 µF (3), 2.2 µF (1)

1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MIST.1010 by UzixLS, Tensigral lamp by cnlohr, Ctf shittyaddon by urish and Cbs badge by cbs-ntcore.

The ATtiny45-20SU in open source designs

The gallery holds 13 open source boards using the ATtiny45-20SU from 13 GitHub repositories; a typical one measures about 65 × 56.5 mm and carries around 35 components.

92% are two-layer designs, the rest use four layers or more, and 62% carry an open source license.

The most starred is MIST.1010 by UzixLS.

Microcontrollers on boards using the ATtiny45-20SU

ATtiny45-20SU: common questions

Where can I find a ATtiny45-20SU reference design?

Each of the 13 boards on this page is a real design using the ATtiny45-20SU. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the ATtiny45-20SU VCC pin?

The VCC pin has a decoupling capacitor on 10 of 12 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 13 open source designs using the ATtiny45-20SU.

What resistor goes on the ATtiny45-20SU XTAL2/PB4 pin?

The XTAL2/PB4 pin has a series resistor on 6 of 13 designs, most often 470 Ω (then 5.6 kΩ). Counted from the KiCad layouts of 13 open source designs using the ATtiny45-20SU.

What resistor goes on the ATtiny45-20SU AREF/PB0 pin?

The AREF/PB0 pin has a series resistor on 6 of 13 designs, most often 22 Ω (then 560 Ω). Counted from the KiCad layouts of 13 open source designs using the ATtiny45-20SU.

Which microcontrollers do boards using the ATtiny45-20SU use?

Most are built on AVR/Arduino (10), ESP8266 (2) and STM32 (1).

How big is a typical board using the ATtiny45-20SU?

The median is 65 × 56.5 mm, and 92% are two-layer designs.

What is the most popular open source board using the ATtiny45-20SU?

By GitHub stars, MIST.1010 by UzixLS, with 43 stars.

Can I simulate one of these boards using the ATtiny45-20SU before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part