Soilsense

wasylews·soilsense·design/soilsense/soilsense.kicad_pcb

Soilsense PCB layout, top view — open source ESP8266 board by wasylews

About the Soilsense PCB

Soilsense is an open source ESP8266 PCB design by wasylews, published on GitHub. It is a 10-layer board measuring 70 × 50 mm, with 25 components from 14 distinct parts.

Its main chip is the ESP-01, from the ESP8266 family. Other key parts include the CapSoilSensor_v1.2, ADS1115IDGS, MCP1700x-330xxTO and GXHT30. By type, the board carries 11 resistors, 6 capacitors, 5 ICs, 2 transistors and 1 diode.

It belongs with the iot & wireless, sensors and power & battery designs in this gallery.

From the project

A low-power soil moisture and climate sensor on an ESP-01, powered by a single 18650 cell for an estimated six months. Custom PCB and a 3D-printed enclosure.

A low-power soil moisture and climate sensor for your garden. It samples capacitive soil moisture, temperature, and humidity, then reports them to Home Assistant. The whole device runs on an ESP-01 and is powered by a single 18650 cell, good for roughly six months per charge. It lives in a 3D-printed enclosure you can print at home.

- Battery-operated ESP-01 that deep-sleeps between readings to stretch battery life - Single 18650 cell, estimated six months per charge - Capacitive soil moisture probe sampled through an ADS1115 ADC - GXHT30 digital temperature and humidity sensor - Publishes…

Soilsense, from the project README
From the project README

Main components on the Soilsense

CapSoilSensor_v1.2ADS1115IDGSMCP1700x-330xxTOGXHT30ESP-01

Soilsense bill of materials (BOM)

25 components, 14 distinct parts.

QtyPartRefs
1
CapSoilSensor_v1.2
U2
1
ADS1115IDGS
U3
1
MCP1700x-330xxTO
U4
1
GXHT30
U5
1
ESP-01
U6
2
AO3407
Q1, Q2
1
1N5819
D1
4
100nF
C1, C4, C5, C6
2
10uF
C2, C3
5
100K
R1, R4, R5, R8, R9
1
100
R2
1
220K
R3
2
10K
R6, R7
2
4.7K
R10, R11

Soilsense design files

The KiCad project lives in the wasylews/soilsense repository on GitHub; these links point at the commit this page was built from.

Soilsense: common questions

What microcontroller does the Soilsense use?

The Soilsense is built around the ESP-01, from the ESP8266 family.

How big is the Soilsense PCB?

The Soilsense measures 70 × 50 mm, has 10 copper layers and is 1.6 mm thick.

How many components are on the Soilsense?

25 components, from 14 distinct parts. The full bill of materials is listed on this page.

Where can I download the Soilsense design files?

From the wasylews/soilsense repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Soilsense design in my own project?

The repository has no license, so all rights stay with wasylews. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Soilsense without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP8266 firmware against it before you order a PCB.

More boards in soilsense

Similar boards