16 open source boards using the ESP-01
Real designs built with the ESP-01, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP8266
DMX CTRL
michar71
50 × 100 mm43 parts2LNo license12ESP8266
Luminator-Flipdot-Display
tylerebowers
287.5 × 109.2 mm109 parts4LNo license5ESP8266
CT800
d3rvita
204.5 × 121.9 mm79 parts2LMIT4ESP8266
Soil Sensor Hub
ArtoLabs
98 × 91.1 mm74 parts2LMIT3STM32
Chronolog
slemanz
100 × 50 mm87 parts4LNo license2RP2040/RP2350
Ppse hardware
4137314
102.2 × 77.2 mm134 parts2LGPL-3.01ESP8266
Dimled mini
tqlabs-in
50 × 24.5 mm15 parts2LMIT1ESP8266
Soilsense esp right
wasylews
70 × 30 mm26 parts10LNo license0ESP8266
Esp01-led controller
eritbh
11.7 × 33.8 mm22 parts2LCC0-1.00ESP8266
Environment Controller KiCad THT
ArtoLabs
96 × 73 mm45 parts2LMIT3ESP8266
Soilsense
wasylews
70 × 50 mm25 parts10LNo license0ESP8266
Soilsense-30x70
wasylews
70 × 32.5 mm25 parts10LNo license0ESP8266
DASHBOARD
luftaquila
225.1 × 97 mm56 parts2LNo license1ESP8266
Soilsense-50x70
wasylews
70 × 50 mm25 parts10LNo license0ESP8266
Soilsense alternative
wasylews
70 × 32.5 mm25 parts10LNo license0ESP8266
Wled esp01-controller
amitesh-singh
38.5 × 33 mm9 parts2LGPL-3.01
How designs wire the ESP-01
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the ESP-01 connects to, and the resistors, capacitors and other passives placed on it.
- The IO2 pin has a pull-up to 3.3V on 4 of 10 designs, most often 1 kΩ (then 10 kΩ).
- The IO0 pin has a pull-up to 3.3V on 4 of 10 designs, most often 10 kΩ (then 1 kΩ).
- The CH_PD pin has a pull-up to 3.3V on 4 of 10 designs, most often 10 kΩ (then 4.7 kΩ).
- The RST pin has a pull-up to 3.3V on 4 of 10 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| IO2pin 2 | Connected to: A connector 20% · not connected 30% · GND 20% |
|
| IO0pin 3 | Connected to: A connector 20% · not connected 40% |
|
| CH_PDpin 6 | Connected to: The microcontroller 20% · 3.3V 20% |
|
| RSTpin 7 | Connected to: The microcontroller 20% · 3.3V 30% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include DMX CTRL by michar71, CT800 PCB by d3rvita, Environment Controller KiCad THT by ArtoLabs and Chronolog by slemanz.
The ESP-01 in open source designs
The gallery holds 16 open source boards using the ESP-01 from 11 GitHub repositories; a typical one measures about 70 × 50 mm and carries around 35 components.
56% are two-layer designs, the rest use four layers or more, and 44% carry an open source license.
The most starred is DMX CTRL by michar71.
Microcontrollers on boards using the ESP-01
What boards using the ESP-01 are built for
ESP-01: common questions
Where can I find a ESP-01 reference design?
Each of the 16 boards on this page is a real design using the ESP-01. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the ESP-01 IO2 pin?
The IO2 pin has a pull-up to 3.3V on 4 of 10 designs, most often 1 kΩ (then 10 kΩ). Counted from the KiCad layouts of 10 open source designs using the ESP-01.
What pull-up resistor is used on the ESP-01 IO0 pin?
The IO0 pin has a pull-up to 3.3V on 4 of 10 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 10 open source designs using the ESP-01.
What pull-up resistor is used on the ESP-01 CH_PD pin?
The CH_PD pin has a pull-up to 3.3V on 4 of 10 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 10 open source designs using the ESP-01.
Which microcontrollers do boards using the ESP-01 use?
Most are built on ESP8266 (14), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the ESP-01?
The median is 70 × 50 mm, and 56% are two-layer designs.
What is the most popular open source board using the ESP-01?
By GitHub stars, DMX CTRL by michar71, with 12 stars.
Can I simulate one of these boards using the ESP-01 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.