OpenWatch
willherr72·OpenWatch·KiCad/Smartwatch.kicad_pcb
About the OpenWatch PCB
OpenWatch is an open source ESP32 PCB design by willherr72, published on GitHub. It is a 4-layer board measuring 38.5 × 38.5 mm, with 94 components from 42 distinct parts.
Its main chip is the ESP32-S3, from the ESP32 family. Other key parts include the BNO055, MIC5504-3.3YM5, MAX30102, MCP9808_DFN and TPS2116DRL. By type, the board carries 35 capacitors, 29 resistors, 13 ICs, 3 crystals, 3 diodes and 2 antennas.
It belongs with the wearables designs in this gallery.
From the project
Open source smart watch based on ESP32-S3
An open-source smartwatch project developed as a school final project. This repository contains all the necessary files for building a complete smartwatch, including mechanical designs, PCB layouts, and firmware/software code.
- Git - Version control system - KiCad - For PCB design and schematic editing - SolidWorks (or compatible CAD software) - For mechanical design files - Arduino IDE - For firmware development - Code editor (VSCode, Cursor, etc.) - For software development
Main components on the OpenWatch
OpenWatch bill of materials (BOM)
94 components, 42 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | BNO055 | LGA-28_5.2x3.8mm_P0.5mm | U1 |
| 1 | MIC5504-3.3YM5 | SOT-23-5 | U2 |
| 1 | MAX30102 | Maxim_OLGA-14_3.3x5.6mm_P0.8mm | U3 |
| 1 | MCP9808_DFN | DFN-8-1EP_3x2mm_P0.5mm_EP1.7x1.4mm | U4 |
| 1 | TPS2116DRL | SOT-583-8 | U5 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U6 |
| 1 | BRCL4054DME | SOT-23-5 | U7 |
| 1 | GC9A01_IPS_DISPLAY_W/_TOUCH GC9A01_IPS_Display_w/_Touch | JST_ZE_B13B-ZESK-D_1x13_P1.50mm_Vertical | U9 |
| 1 | Quectel LC76G | quectel lc76g | U10 |
| 1 | MIC5504-1.8YM5 | SOT-23-5 | U11 |
| 1 | ESP32-S3 | QFN-56-1EP_7x7mm_P0.4mm_EP4x4mm | U12 |
| 1 | BMP280 | Bosch_LGA-8_2x2.5mm_P0.65mm_ClockwisePinNumbering | U13 |
| 1 | LD39100PU33R | DFN-6-1EP_3x3mm_P0.95mm_EP1.7x2.6mm | U14 |
| 1 | LCM1027B3605F | PinHeader_1x02_P1.27mm_Vertical | M1 |
| 1 | AO3400A | TSOT-23 | Q1 |
| 1 | 40MHZ 40MHz | Crystal_SMD_2016-4Pin_2.0x1.6mm | Y1 |
| 2 | 32.768KHZ 32.768KHz | EPSON Q13FC13500004 | Y2, Y3 |
| 1 | 5358 | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | Antenna_Shield | L_1206_3216Metric | AE1 |
| 1 | W3011 | L_1206_3216Metric | AE2 |
Show 22 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 1S1P LiPo | PinHeader_1x02_P1.27mm_Vertical | BT1 |
| 1 | BOOT SEL | SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1 |
| 1 | SW_Push | JXTCONN TS-1010-S26 | SW1 |
| 1 | JXTCONN TS-1010-S26 | JXTCONN TS-1010-S26 | SW2 |
| 3 | D_Small | D_SOD-323 | D1, D2, D3 |
| 2 | 0 | R_0402_1005Metric | L1, L2 |
| 2 | 1u | C_0402_1005Metric | C1, C6 |
| 5 | 10U 10u | C_0603_1608Metric | C2, C8, C10, C22, C35 |
| 17 | 100N 100n | C_0402_1005Metric | C3, C4, C5, C9, C11, C12, C13, C14 +9 |
| 1 | 10U 10u | C_0402_1005Metric | C7 |
| 2 | 10P 10p | C_0402_1005Metric | C15, C16 |
| 4 | 22P 22p | C_0402_1005Metric | C17, C18, C31, C32 |
| 4 | DNP | C_0402_1005Metric | C27, C28, C33, C34 |
| 1 | 10 | R_0402_1005Metric | R1 |
| 14 | 10K 10k | R_0402_1005Metric | R2, R3, R6, R10, R14, R15, R16, R19 +6 |
| 3 | 0 | R_0402_1005Metric | R4, R24, R25 |
| 3 | 1k | R_0402_1005Metric | R5, R8, R9 |
| 2 | 1M | R_0402_1005Metric | R7, R11 |
| 1 | 250K | R_0402_1005Metric | R12 |
| 1 | 2K | R_0402_1005Metric | R13 |
| 2 | 4.7K 4.7k | R_0402_1005Metric | R17, R18 |
| 2 | 22 | R_0402_1005Metric | R27, R28 |
OpenWatch design files
The KiCad project lives in the willherr72/OpenWatch repository on GitHub; these links point at the commit this page was built from.
OpenWatch: common questions
What microcontroller does the OpenWatch use?
The OpenWatch is built around the ESP32-S3, from the ESP32 family.
How big is the OpenWatch PCB?
The OpenWatch measures 38.5 × 38.5 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the OpenWatch?
94 components, from 42 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the OpenWatch design files?
From the willherr72/OpenWatch repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the OpenWatch design in my own project?
The repository has no license, so all rights stay with willherr72. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the OpenWatch without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k