UControl v3
wyolum·uControl_v3·KiCAD/uControl_v3.kicad_pcb
About the UControl v3 PCB
UControl v3 is an open source AVR/Arduino PCB design by wyolum, published on GitHub under the MIT license. It is a 2-layer board measuring 190 × 152 mm, with 147 components from 75 distinct parts.
Its main chip is the ATMEGA328-AU-ND, from the AVR/Arduino family. Other key parts include the TXB0104D, TPS62133, TPS62132, DS3231N and TSX0108. By type, the board carries 39 capacitors, 27 resistors, 26 connectors, 9 ICs, 8 diodes and 6 switches.
From the project
Blood Pressure Monitor
Main components on the UControl v3
UControl v3 bill of materials (BOM)
147 components, 75 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TXB0104D | TXB0104D | U1 |
| 1 | TPS62133 | TPS62132 | U3 |
| 1 | TPS62132 | TPS62132 | U4 |
| 1 | DS3231N | DS3231 | U5 |
| 1 | ATMEGA328-AU-ND | TQFP32 | U7 |
| 1 | TSX0108 | TXS0108EPWR | U8 |
| 1 | CAT24C256 | SO8E | U9 |
| 1 | BEAGLEBONE | BEAGLEBONE | U10 |
| 1 | ADXL345 | ADXL345 | U11 |
| 4 | BCP5416TA | SOT223 | Q1, Q2, Q3, Q4 |
| 1 | 2N7002KW | SOT323 | Q5 |
| 1 | 16MHz | Xtal_SMD3 | X1 |
| 1 | 5V_EXT | Header_2 | J1 |
| 1 | 3V3_EXT | Header_2 | J2 |
| 1 | addr | Header_2x2 | J3 |
| 1 | AREF | ShortLink2 | P1 |
| 1 | ICSP | Header_ISP | P4 |
| 1 | FTDI | Header_FTDI | P5 |
| 1 | GAGE_PR | HCEM500GUH9P3 | P7 |
| 1 | ABSO_PR | HDIB002AUY8H5 | P8 |
Show 55 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | C3SB | pin_strip_4-90 | P9, P10 |
| 1 | VSel_Vlv | Header_3 | P11 |
| 1 | PWR_IN | Header_2 | P13 |
| 1 | X_VALVE | X_Valve_2 | P14 |
| 1 | Flow_Conn | Conn_Flow_SFM3000_Male | P15 |
| 1 | FLOWMETER | FlowMeter_SFM3000 | P16 |
| 1 | PUMP | Pump_P54E01R_02 | P17 |
| 1 | U6_OE | ShortLink2 | P19 |
| 1 | 5V_LINK | ShortLink2 | P20 |
| 2 | CONN_23X2 | PIN_ARRAY_23X2 | P21, P22 |
| 1 | Alt_Add | ShortLink2 | P23 |
| 1 | PWR_IN | JACK_ALIM | P24 |
| 1 | Int1 | ShortLink2 | P28 |
| 1 | Int2 | ShortLink2 | P29 |
| 1 | VSel_Vlv2 | Header_3 | P34 |
| 1 | X_VALVE2 | X_Valve_2 | P38 |
| 3 | I_O | I_O | B1, B2, B3 |
| 2 | PB0 | I_O | B4, B12 |
| 1 | 5V_ATMega | I_O | B5 |
| 1 | 3V3_BBB | I_O | B6 |
| 1 | PC0 | I_O | B8 |
| 1 | PC1 | I_O | B9 |
| 1 | PC6 | I_O | B10 |
| 1 | PC7 | I_O | B11 |
| 1 | BATT_HOLDER | CR2032 | BT1 |
| 1 | PCB | PCB | PCB1 |
| 10 | SCREW | vite_3mm | SC1, SC2, SC3, SC4, SC5, SC6, SC7, SC8 +2 |
| 1 | BUZZER | Speaker | SP1 |
| 1 | Reset | SW_PB_V_H | SW1 |
| 1 | INT0 | SW_PB_V_H | SW2 |
| 1 | INT1 | SW_PB_V_H | SW3 |
| 1 | PWR_BBB | SW_PB_V_H | SW4 |
| 1 | GPIO1_6 | SW_PB_V_H | SW5 |
| 1 | GPIO1_29 | SW_PB_V_H | SW6 |
| 4 | S1D-13-F | diode-DO214AC | D1, D3, D4, D9 |
| 1 | 5V0 | led_0805 | D5 |
| 1 | 3V3 | led_0805 | D6 |
| 1 | BLINK | led_0805 | D7 |
| 1 | 12V | led_0805 | D8 |
| 2 | 2u2H,3.0A | Inductor_SMD3 | L1, L2 |
| 25 | 100nF | c_0805 | C1, C4, C5, C7, C8, C9, C10, C11 +17 |
| 2 | 22pF | c_0603 | C2, C3 |
| 2 | 22uF X7R | c_1210 | C19, C33 |
| 2 | 3.3nF | c_0805 | C21, C35 |
| 6 | 100uF | C_ELCO_SMD | C22, C26, C27, C36, C37, C42 |
| 2 | 10uF X7R | c_1206 | C30, C38 |
| 10 | 10k | r_0805 | R1, R2, R3, R4, R11, R15, R21, R22 +2 |
| 2 | 4k7 | r_0805 | R5, R12 |
| 3 | 1k | r_0805 | R6, R10, R13 |
| 2 | 100k | r_0805 | R7, R14 |
| 1 | 330E | r_0805 | R8 |
| 1 | 120E | r_0805 | R9 |
| 4 | 4k75 | r_0805 | R16, R17, R18, R23 |
| 2 | 1k5 | r_0805 | R19, R20 |
| 2 | 220 | r_0805 | R24, R25 |
UControl v3 design files
The KiCad project lives in the wyolum/uControl_v3 repository on GitHub; these links point at the commit this page was built from.
UControl v3: common questions
What microcontroller does the UControl v3 use?
The UControl v3 is built around the ATMEGA328-AU-ND, from the AVR/Arduino family.
How big is the UControl v3 PCB?
The UControl v3 measures 190 × 152 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the UControl v3?
147 components, from 75 distinct parts. The full bill of materials is listed on this page.
Where can I download the UControl v3 design files?
From the wyolum/uControl_v3 repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the UControl v3 design in my own project?
Yes, under the terms of its MIT license, which wyolum chose for the repository.
Can I test firmware for the UControl v3 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k