14 open source boards using the TPS62133

Real designs built with the TPS62133, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

14 boardsClear filters|Most starred

How designs wire the TPS62133

Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the TPS62133 connects to, and the resistors, capacitors and other passives placed on it.

  • The SW pins have a inductor on 8 of 9 designs, most often 2.2 µH (then 22 µH).
  • The SS/TR pin has a capacitor to GND on 7 of 8 designs, most often 3.3 nF (then 10 nF).
  • The AVIN pin has a decoupling capacitor on 7 of 8 designs, most often 10 µF (then 100 nF).
  • The FSW pin is tied to GND on 8 of 8 designs.
SWpin 1, 2, 3Connected to: Signal 96%
  • Inductor on 89% · 2.2 µH (21), 22 µH (3)
PGpin 4Connected to: Signal 78%
  • Pull-up to 5V on 44% · 100 kΩ (3), 10 kΩ (1)
  • Series resistor on 33% · 100 kΩ (3)
FBpin 5Connected to: GND 88%
GNDpin 6, 15, 16, 17Connected to: GND 93%
FSWpin 7Connected to: GND 100%
DEFpin 8Connected to: GND 100%
SS/TRpin 9Connected to: Signal 100%
  • Capacitor to GND on 88% · 3.3 nF (6), 10 nF (1)
AVINpin 10Connected to: 12V 75% · a signal 25%
  • Decoupling capacitor on 88% · 10 µF (6), 100 nF (4), 100 µF (4)
PVINpin 11, 12Connected to: 12V 75% · a signal 25%
  • Decoupling capacitor on 75% · 10 µF (10), 100 nF (8), 100 µF (8)
ENpin 13Connected to: 12V 63% · a signal 38%
VOSpin 14Connected to: 5V 63% · a signal 38%
  • Decoupling capacitor on 50% · 22 µF (3), 10 µF (2)
  • Inductor on 38% · 2.2 µH (2), 22 µH (1)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include M4psu by cuspaceflight, QRE MiniBoards by bismarx-v1, SUMEC MK IV by bismarx-v1 and TiNA - Controller for TiM by wyolum.

The TPS62133 in open source designs

The gallery holds 14 open source boards using the TPS62133 from 9 GitHub repositories; a typical one measures about 85 × 57.4 mm and carries around 93 components.

79% are two-layer designs, the rest use four layers or more, and 29% carry an open source license.

The most starred is M4psu by cuspaceflight.

Microcontrollers on boards using the TPS62133

What boards using the TPS62133 are built for

TPS62133: common questions

Where can I find a TPS62133 reference design?

Each of the 14 boards on this page is a real design using the TPS62133. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the TPS62133 SW pin connected?

The SW pins have a inductor on 8 of 9 designs, most often 2.2 µH (then 22 µH). Counted from the KiCad layouts of 9 open source designs using the TPS62133.

How is the TPS62133 SS/TR pin connected?

The SS/TR pin has a capacitor to GND on 7 of 8 designs, most often 3.3 nF (then 10 nF). Counted from the KiCad layouts of 9 open source designs using the TPS62133.

What decoupling capacitors do designs use on the TPS62133 AVIN pin?

The AVIN pin has a decoupling capacitor on 7 of 8 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 9 open source designs using the TPS62133.

What parts are used alongside the TPS62133?

The ADXL345, ATMEGA328-AU-ND, BEAGLEBONE, CAT24C256 and DS3231N appear in the most repositories here.

Which microcontrollers do boards using the TPS62133 use?

Most are built on ESP32 (5), AVR/Arduino (4) and STM32 (2).

How big is a typical board using the TPS62133?

The median is 85 × 57.4 mm, and 79% are two-layer designs.

What is the most popular open source board using the TPS62133?

By GitHub stars, M4psu by cuspaceflight, with 8 stars.

Can I simulate one of these boards using the TPS62133 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part