Cm5

YORROY123·kicad-scripted-pcb·boards/cm5/cm5.kicad_pcb

Cm5 PCB layout, top view — open source Raspberry Pi board by YORROY123

About the Cm5 PCB

Cm5 is an open source Raspberry Pi PCB design by YORROY123, published on GitHub under the MIT license. It is a 4-layer board measuring 170 × 120 mm, with 221 components from 81 distinct parts.

Its main chip is the CM5 pins 1-100, from the Raspberry Pi family. Other key parts include the LM5146RGYR, TPS568230RJER, TPD4EUSB30, LAN7800/Y9X and IP804AR. By type, the board carries 115 capacitors, 52 resistors, 13 connectors, 12 ICs, 12 diodes and 4 inductors.

From the project

Three KiCad 10 PCBs designed entirely as Python code with layered verification

Raspberry Pi Compute Module 5(含 eMMC)的通用載板,目標是 JLCPCB 能直接 PCBA,CM5 自己插上。

原理圖已完成。PCB 進行中:擺件完成、還沒佈線。3D 預覽在 concept/。

gen/pcb.py 讀網表擺出 cm5.kicadpcb;座標與自動擺件在 gen/placement.py`,3D 預覽也用同一份。

- 170 × 120 mm、4 層。固定孔:板子 M3 ×4(H1–H4),CM5 模組 M2.5 ×4(H5–H8)。 - 網路類別:HV54(+54V、POE、SW;0.5 mm 線、0.25 mm 間距)、Rail(+5V、+3V3、SW3;0.8 mm)、 Power(GND 與其他小電源;0.5 mm)。54 V 間距取 IPC-2221 表 6-1 的 B4(外層有防焊,51–100 V 0.13 mm)再留餘量;B2(無塗層)的 0.6 mm 零件本身做不到(RJ45 腳間 0.53、IP804AR 0.25)。 - cm5.kicaddru:同一顆零件的焊盤之間最小 0.1 mm(FSUSB42 MSOP-10 焊盤間只有 0.15 mm), 走線與過孔仍照網路類別。拿掉這個檔,DRC 會報 FSUSB42 的 8 個間距錯誤。 -…

Main components on the Cm5

Cm5 bill of materials (BOM)

221 components, 81 distinct parts.

QtyPartRefs
1
LM5146RGYR
U10
1
TPS568230RJER
U20
2
TPD4EUSB30
U30, U31
2
LAN7800/Y9X
U40, U41
1
IP804AR
U50
1
FSUSB42MUX
U60
1
USB2514B
U61
2
AP2171W
U62, U63
1
TPS2051CDBV
U70
1
BSC160N10NS3G
Q10
1
BSC070N10NS5
Q11
2
25MHz
Y40, Y41
1
24MHz
Y60
1
CM5 pins 1-100
J1
1
CM5 pins 101-200
J2
1
54V IN
J20
1
HR911130A
J30
1
POE0
J40
1
POE1
J41
1
USB-C FLASH
J50
Show 61 more
QtyPartRefs
1
USB-A 1
J51
1
USB-A 2
J52
1
M.2 M-key
J60
1
HDMI
J70
1
GPIO 40-pin
J80
1
FAN
J81
1
CR2032
BT50
1
4A 63V
F1
2
1.5A
F40, F41
1
POWER
SW50
1
FLASH/RUN
SW51
2
G2423S
T40, T41
3
SM6T68A
D20, D60, D61
3
GREEN
D40, D42, D51
2
YELLOW
D41, D43
1
RED
D50
3
USBLC6-2SC6
D70, D71, D72
1
3.3uH SPM10065VT
L10
1
1.5uH IHLP4040
L20
2
3.3uH
L40, L41
1
100uF
C10
6
4.7uF
C11, C12, C13, C14, C15, C16
1
100nF
C17
1
47nF
C18
1
15pF
C19
1
2.2uF
C20
56
100nF
C21, C47, C49, C51, C60, C70, C71, C72 +48
1
6.8nF
C22
1
150pF
C23
1
820pF
C24
14
47uF
C30, C31, C32, C33, C34, C40, C41, C42 +6
1
100pF
C44
7
1uF
C48, C105, C117, C135, C147, C210, C213
1
1uF
C82
1
47uF
C83
5
4.7uF
C84, C85, C86, C87, C201
2
1nF 2kV
C90, C91
2
100nF
C92, C93
4
10uF
C100, C110, C130, C140
6
27pF
C118, C119, C148, C149, C208, C209
2
100uF
C211, C214
1
402k
R10
1
12.4k
R11
1
33.2k
R12
1
412
R13
1
23.2k
R14
1
4.42k
R15
1
7.5k
R16
1
150
R17
16
10k
R18, R74, R75, R76, R77, R78, R102, R103 +8
1
91k
R21
1
20k
R22
1
330k
R23
3
5.1k
R24, R200, R201
4
100k
R25, R202, R203, R204
2
1k
R50, R51
6
470
R60, R61, R104, R105, R134, R135
4
75
R80, R81, R82, R83
2
2k
R100, R130
3
12k
R101, R131, R210
1
1M
R211

Cm5 design files

The KiCad project lives in the YORROY123/kicad-scripted-pcb repository on GitHub; these links point at the commit this page was built from.

Cm5: common questions

What microcontroller does the Cm5 use?

The Cm5 is built around the CM5 pins 1-100, from the Raspberry Pi family.

How big is the Cm5 PCB?

The Cm5 measures 170 × 120 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Cm5?

221 components, from 81 distinct parts. The full bill of materials is listed on this page.

Where can I download the Cm5 design files?

From the YORROY123/kicad-scripted-pcb repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Cm5 design in my own project?

Yes, under the terms of its MIT license, which YORROY123 chose for the repository.

Can I test firmware for the Cm5 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.

More boards in kicad-scripted-pcb

Similar boards