5 open source boards using the USB2514B
Real designs built with the USB2514B, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Nanoberry
EnzoRF
85 × 56 mm229 partsGPL-3.021Raspberry Pi
Unifying
balthazar-space
120.9 × 78.8 mm121 parts4LCERN-OHL-S-2.07Raspberry Pi
Cm5
YORROY123
170 × 120 mm221 parts4LMIT1ReTerminalEM-NVMe mPCIe-USB
stanleyondrus
135 × 90.4 mm58 parts2LNo license23CC Debug
EBOThor
160 × 80 mm215 parts4LMIT0
How designs wire the USB2514B
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the USB2514B connects to, and the resistors, capacitors and other passives placed on it.
- The HS_IND/CFG_SEL1 pin has a resistor to GND on 5 of 5 designs, most often 100 kΩ (then 36 kΩ).
- The RBIAS pin has a resistor to GND on 5 of 5 designs, most often 12 kΩ.
- The VDDA33 pins have a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF).
- The VDD33 pins have a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDA33pin 5, 10, 29, 36 | Connected to: 3.3V 100% |
|
| USBDM_DN3/PRT_DIS_M3pin 6 | Connected to: A connector 60% |
|
| USBDP_DN3/PRT_DIS_P3pin 7 | Connected to: A connector 60% |
|
| USBDM_DN4/PRT_DIS_M4pin 8 | Connected to: A connector 60% |
|
| USBDP_DN4/PRT_DIS_P4pin 9 | Connected to: A connector 60% |
|
| TESTpin 11 | Connected to: GND 60% · not connected 40% | — |
| OCS_N1pin 13 | Connected to: Signal 80% · not connected 20% |
|
| CRFILTpin 14 | Connected to: Signal 60% · not connected 40% |
|
| VDD33pin 15, 23 | Connected to: 3.3V 100% |
|
| PRTPWR2/BC_EN2pin 16 | Connected to: Not connected 60% · a signal 40% | — |
| OCS_N2pin 17 | Connected to: Signal 80% · not connected 20% |
|
| PRTPWR3/BC_EN3pin 18 | Connected to: Not connected 80% · a signal 20% | — |
| PRTPWR4/BC_EN4pin 20 | Connected to: Not connected 80% · a signal 20% | — |
| SDA/SMBDATA/NON_REM1pin 22 | Connected to: Signal 100% |
|
| SCL/SMBCLK/CFG_SEL0pin 24 | Connected to: Signal 100% |
|
| HS_IND/CFG_SEL1pin 25 | Connected to: Signal 100% |
|
| RESET_Npin 26 | Connected to: Signal 100% |
|
| VBUS_DETpin 27 | Connected to: 3.3V 100% |
|
| SUSP_IND/LOCAL_PWR/NON_Rpin 28 | Connected to: Signal 80% · not connected 20% |
|
| XTALOUTpin 32 | Connected to: Signal 80% · not connected 20% |
|
| XTALIN/CLKINpin 33 | Connected to: Signal 100% |
|
| PLLFILTpin 34 | Connected to: Signal 60% · not connected 40% |
|
| RBIASpin 35 | Connected to: Signal 100% |
|
| VSSpin 37 | Connected to: GND 100% | — |
9 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ReTerminalEM-NVMe mPCIe-USB by stanleyondrus, Nanoberry by EnzoRF, Unifying-PCB by balthazar-space and Cm5 by YORROY123.
The USB2514B in open source designs
The gallery holds 5 open source boards using the USB2514B from 5 GitHub repositories; a typical one measures about 135 × 80 mm and carries around 215 components.
75% use four copper layers or more, and 80% carry an open source license.
The most starred is ReTerminalEM-NVMe mPCIe-USB by stanleyondrus.
Parts used alongside the USB2514B
Microcontrollers on boards using the USB2514B
What boards using the USB2514B are built for
USB2514B: common questions
Where can I find a USB2514B reference design?
Each of the 5 boards on this page is a real design using the USB2514B. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the USB2514B HS_IND/CFG_SEL1 pin?
The HS_IND/CFG_SEL1 pin has a resistor to GND on 5 of 5 designs, most often 100 kΩ (then 36 kΩ). Counted from the KiCad layouts of 5 open source designs using the USB2514B.
What resistor goes on the USB2514B RBIAS pin?
The RBIAS pin has a resistor to GND on 5 of 5 designs, most often 12 kΩ. Counted from the KiCad layouts of 5 open source designs using the USB2514B.
What decoupling capacitors do designs use on the USB2514B VDDA33 pin?
The VDDA33 pins have a decoupling capacitor on 4 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the USB2514B.
Which microcontrollers do boards using the USB2514B use?
Most are built on Raspberry Pi (2).
How big is a typical board using the USB2514B?
The median is 135 × 80 mm, and 25% are two-layer designs.
What is the most popular open source board using the USB2514B?
By GitHub stars, ReTerminalEM-NVMe mPCIe-USB by stanleyondrus, with 23 stars.
Can I simulate one of these boards using the USB2514B before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.