Mainboard
Cluradev·CluraEnclosure·PCBs/kicad/mainboard.kicad_pcb
About the Mainboard PCB
Mainboard is an open source STM32 PCB design by Cluradev, published on GitHub. It is a 4-layer board measuring 120 × 90 mm, with 162 components from 72 distinct parts.
Its main chip is the STM32F411CEUx, from the STM32 family. Other key parts include the USBLC6-2P6, TPD6E05U06RVZ, L7809, USBLC6-4SC6 and AT24CS64-SSHM. By type, the board carries 45 resistors, 29 diodes, 28 capacitors, 16 ICs, 7 transistors and 6 connectors.
It belongs with the displays & leds designs in this gallery.
From the project
This is the Offical Repo of the Clura Enclosure. Here you will find everything that we have ever made. Enjoy! For more details visit our site: clura.dev
Open hardware KiCad 9 designs for a two-board set: an STM32F411-based mainboard that handles power, control and I/O, and a companion sensorboard carrying the gas/smoke sensing front end. The two connect over an RJ45 link.
- MCU — STM32F411CEU6, 25 MHz HSE + 32.768 kHz LSE crystals, SWD header, BOOT jumper - Storage — micro SD card slot, AT24CS64 I²C EEPROM - Power — 12 V input via barrel jack / screw terminal, LM2596 switchers for 12 V and 5 V rails, SY8120B for 3V3, dedicated +5 V servo rail, fuse and reverse-protection diode - I/O — RJ45 to the sensorboard, HX711 load-cell interface…

Main components on the Mainboard
Mainboard bill of materials (BOM)
162 components, 72 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 7 | USBLC6-2P6 | SOT-666 | U1, U2, U3, U4, U5, U8, U12 |
| 1 | STM32F411CEUx | QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm | U6 |
| 1 | TPD6E05U06RVZ | Texas_R-PUSON-N14 | U7 |
| 1 | L7809 | TO-263-2 | U9 |
| 1 | USBLC6-4SC6 | SOT-23-6 | U10 |
| 1 | AT24CS64-SSHM | SOIC-8_3.9x4.9mm_P1.27mm | U13 |
| 2 | LM2596S-5 | TO-263-5_TabPin3 | U18, U21 |
| 1 | LM2596S-12 | TO-263-5_TabPin3 | U19 |
| 1 | SY8120B | SOT23-6 | U22 |
| 2 | Motor_Servo | PinHeader_1x03_P2.54mm_Vertical | M1, M2 |
| 1 | MOSFET-FAN | SOT-23 | Q1 |
| 3 | BSS138 | SOT-23 | Q2, Q3, Q4 |
| 3 | SS8050 | SOT-23 | Q5, Q6, Q7 |
| 1 | 25MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 32.768KHz | Crystal_C38-LF_D3.0mm_L8.0mm_Horizontal | Y2 |
| 1 | pms5003 | JST_GH_SM08B-GHS-TB_1x08-1MP_P1.25mm_Horizontal | J1 |
| 1 | LED Strip | JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J2 |
| 1 | POWER IN TERMINAL | BarrelJack_Horizontal | J3 |
| 1 | SWD HEADER | PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | Power_Out | JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J6 |
Show 52 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SWITCH | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J12 |
| 1 | Buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | RJ45_NEW | RJ45_NEW | CONN1 |
| 1 | 3A | FUSE_01550900M | F1 |
| 2 | 140mm_FAN | Molex_KK-254_AE-6410-04A_1x04_P2.54mm_Vertical | FAN1, FAN6 |
| 2 | 60mm_FAN | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | FAN2, FAN5 |
| 2 | Fan | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | FAN3, FAN4 |
| 1 | REG FAN JUMPER | PinHeader_2x03_P2.54mm_Vertical_SMD | JP1 |
| 1 | 60MM FAN JUMPER | PinHeader_2x03_P2.54mm_Vertical_SMD | JP2 |
| 1 | 140 MM FAN JUMPER | PinHeader_2x03_P2.54mm_Vertical_SMD | JP3 |
| 1 | Screen | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | JS1 |
| 2 | LOAD CELL AMP | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | LC1, LC2 |
| 1 | F60 | JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | RV1 |
| 1 | F140 | JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | RV2 |
| 1 | Micro_SD_Card_Det1 | microSD_HC_Hirose_DM3AT-SF-PEJM5 | SD1 |
| 1 | BOOT_JP | SW_DIP_SPSTx02_Slide_6.7x6.64mm_W8.61mm_P2.54mm_LowProfile | SW1 |
| 1 | RESET_SW | SW_SPST_PTS647_Sx50 | SW2 |
| 1 | POWER | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | TB1 |
| 1 | 5V SSR TERMINAL1 | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | TB2 |
| 1 | 5V SSR TERMINAL2 | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | TB3 |
| 7 | BSD3A311V | SOD323 | D1, D3, D5, D9, D10, D15, D21 |
| 11 | PESD5V0S1UA | SOD323 | D2, D6, D7, D12, D13, D14, D16, D17 +3 |
| 2 | PESD12VS1UA. | SOD323 | D4, D25 |
| 1 | SS34 | D_SMA | D8 |
| 1 | PRTR5V0U2X | SOT-143 | D11 |
| 3 | PESD3V3L1BA | SOD323 | D18, D19, D24 |
| 1 | S6MC | D_SMC | D26 |
| 3 | SS14 | D_SMA | D27, D28, D29 |
| 2 | 47uH | L_Chilisin_BMRx00060630 | L1, L2 |
| 1 | 47uH | L_APV_APH1050 | L3 |
| 1 | 10uH/SFEK3015A-100M-HF | L_Neosid_SMS-ME3015 | L4 |
| 12 | 0.1uF | C_0603_1608Metric | C1, C2, C4, C5, C11, C12, C13, C15 +4 |
| 1 | 2.2uF | C_0603_1608Metric | C3 |
| 1 | 1uF | C_0603_1608Metric | C6 |
| 2 | 6pF | C_0603_1608Metric | C7, C9 |
| 1 | 10nF | C_0603_1608Metric | C8 |
| 2 | 15pF | C_0603_1608Metric | C10, C14 |
| 1 | 4.7uF | C_0805_2012Metric | C16 |
| 1 | 4.7uF | CP_Elec_10x10.5 | C18 |
| 1 | 4.7uF | C_0603_1608Metric | C19 |
| 3 | 470uF | CP_Elec_10x10.5 | C25, C26, C28 |
| 1 | 100n | C_0603_1608Metric | C29 |
| 1 | 10n | C_0603_1608Metric | C30 |
| 1 | 22u | C_0805_2012Metric | C31 |
| 9 | 100R | R_0603_1608Metric | R1, R2, R3, R5, R6, R15, R16, R34 +1 |
| 15 | 10K | R_0603_1608Metric | R4, R7, R8, R9, R10, R11, R22, R24 +7 |
| 3 | 470R | R_0603_1608Metric | R12, R13, R14 |
| 3 | 220R | R_0603_1608Metric | R17, R23, R27 |
| 11 | 22R | R_0603_1608Metric | R18, R19, R20, R21, R25, R26, R33, R36 +3 |
| 1 | 100k | R_0603_1608Metric | R48 |
| 1 | 22.1k | R_0603_1608Metric | R49 |
| 2 | 0R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R50, R51 |
Mainboard design files
The KiCad project lives in the Cluradev/CluraEnclosure repository on GitHub; these links point at the commit this page was built from.
Mainboard: common questions
What microcontroller does the Mainboard use?
The Mainboard is built around the STM32F411CEUx, from the STM32 family.
How big is the Mainboard PCB?
The Mainboard measures 120 × 90 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Mainboard?
162 components, from 72 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Mainboard design files?
From the Cluradev/CluraEnclosure repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Mainboard design in my own project?
The repository has no license, so all rights stay with Cluradev. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Mainboard without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in CluraEnclosure
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k