CERBERUS

Darkops-cpu·CERBERUS

CERBERUS PCB layout, top view — open source FPGA board by Darkops-cpu

About the CERBERUS PCB

CERBERUS is an open source FPGA PCB design by Darkops-cpu, published on GitHub. It is a 4-layer board measuring 87.3 × 40.5 mm, with 85 components from 40 distinct parts.

Its main chip is the ICE40UP5K-SG48ITR, from the FPGA family. Other key parts include the FT2232HL-REEL, APS6404L-3SQR-SN, LM3880, TLV75512PDBV and TLV75533PDBV. By type, the board carries 32 capacitors, 23 resistors, 8 ICs, 7 diodes, 6 inductors and 4 connectors.

From the project

An open-source iCE40 FPGA development board with a fully open toolchain.

An open-source iCE40 FPGA development board with a fully open toolchain.

No licence server, no 100 GB install. Yosys, nextpnr and IceStorm run on any laptop and synthesise a design this size in seconds.

The FT2232H's two channels run independently, so you can flash a bitstream and watch a UART console at the same time without switching modes.

Download the OSS CAD Suite and add it to your PATH. That's Yosys, nextpnr, IceStorm, Icarus, Verilator, GTKWave and iceprog in one archive. Nothing to compile, nothing to licence.

Main components on the CERBERUS

CERBERUS bill of materials (BOM)

85 components, 40 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
FT2232HL-REEL
IC1
1
APS6404L-3SQR-SN
U1
1
LM3880
U2
1
TLV75512PDBV
U3
1
TLV75533PDBV
U4
1
93LCXXB
93LCxxB
U5
1
W25Q32JVSS
U6
1
ICE40UP5K-SG48ITR
U8
1
ASV-12MHZ
ASV-12MHz
Y2
1
12mhz @ 10pf load
Y3
1
USB_C_RECEPTACLE_USB2.0_16P
USB_C_Receptacle_USB2.0_16P
J1
1
CONN_01X06_PIN
Conn_01x06_Pin
J2
1
CONN_01X13_PIN
Conn_01x13_Pin
J3
1
CONN_01X16_PIN
Conn_01x16_Pin
J4
2
Polyfuse
F1, F2
1
SW_Push
SW1
1
Deep red 660 nm
D1
1
Amber 595 nm
D2
1
Warm white 3000 K
D3
1
Orange 610 nm
D4
Show 20 more
QtyPartRefs
1
Red 625 nm
D5
1
Yellow 585 nm
D6
1
Yellow-green 570 nm
D7
6
FerriteBead
FB1, FB2, FB3, FB4, FB5, FB6
4
100U
100u
C1, C2, C3, C4
22
100N
100n
C5, C7, C8, C9, C10, C11, C12, C13 +14
1
10N
10n
C6
2
12P
12p
C17, C18
1
3.3U
3.3u
C19
2
1u
C29, C32
2
5K1
5k1
R1, R2
1
1K5
1k5
R3
4
33
R4, R20, R21, R22
2
100K
100k
R5, R6
3
330
R7, R15, R16
1
12k @1%
R8
2
1k
R9, R14
6
10K
10k
R10, R12, R13, R18, R19, R23
1
2K2
2k2
R11
1
2k
R17

CERBERUS design files

The KiCad project lives in the Darkops-cpu/CERBERUS repository on GitHub; these links point at the commit this page was built from.

CERBERUS: common questions

What microcontroller does the CERBERUS use?

The CERBERUS is built around the ICE40UP5K-SG48ITR, from the FPGA family.

How big is the CERBERUS PCB?

The CERBERUS measures 87.3 × 40.5 mm, has 4 copper layers and is 1.600198 mm thick.

How many components are on the CERBERUS?

85 components, from 40 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the CERBERUS design files?

From the Darkops-cpu/CERBERUS repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the CERBERUS design in my own project?

The repository has no license, so all rights stay with Darkops-cpu. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the CERBERUS without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug FPGA firmware against it before you order a PCB.

Similar boards