9 open source boards using the LM3880
Real designs built with the LM3880, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
Zynq
juliancoy
120 × 60 mm295 partsMIT75Microchip SAM
Node
ParadigmHyperloop
127 × 127 mm390 parts4LCustom license11BGeigieIntegrated
IRNAS
66.8 × 104.8 mm86 parts2LCustom license6Portable line mixer
sww1235
77.5 × 114.3 mm131 parts4LMIT3Microchip SAM
Robohub prototype v1 05282024
jackfrye
71.7 × 46.9 mm102 parts10LNo license0FPGA
CERBERUS
Darkops-cpu
87.3 × 40.5 mm85 parts4LNo license0FPGA
FPGBA
teejaytiger
78.8 × 40 mm65 parts2LNo license0Microchip SAM
Robohub prototype v1 ddr chip2
jackfrye
71.7 × 46.9 mm102 parts10LNo license0FPGA
Mainboard
teejaytiger
78.8 × 40 mm55 parts4LNo license0
How designs wire the LM3880
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the LM3880 connects to, and the resistors, capacitors and other passives placed on it.
- The FLAG1 pin has a pull-up to 5V on 4 of 7 designs, most often 100 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCCpin 1 | Connected to: 5V 86% | — |
| GNDpin 2 | Connected to: GND 100% | — |
| FLAG1pin 6 | Connected to: Signal 86% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ZynqPCB by juliancoy, Node by ParadigmHyperloop, BGeigieIntegrated by IRNAS and Portable line mixer by sww1235.
The LM3880 in open source designs
The gallery holds 9 open source boards using the LM3880 from 7 GitHub repositories; a typical one measures about 78.8 × 46.9 mm and carries around 102 components.
75% use four copper layers or more, and 22% carry an open source license.
The most starred is ZynqPCB by juliancoy.
Microcontrollers on boards using the LM3880
What boards using the LM3880 are built for
LM3880: common questions
Where can I find a LM3880 reference design?
Each of the 9 boards on this page is a real design using the LM3880. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the LM3880 FLAG1 pin?
The FLAG1 pin has a pull-up to 5V on 4 of 7 designs, most often 100 kΩ. Counted from the KiCad layouts of 7 open source designs using the LM3880.
Which microcontrollers do boards using the LM3880 use?
Most are built on FPGA (4) and Microchip SAM (3).
How big is a typical board using the LM3880?
The median is 78.8 × 46.9 mm, and 25% are two-layer designs.
What is the most popular open source board using the LM3880?
By GitHub stars, ZynqPCB by juliancoy, with 75 stars.
Can I simulate one of these boards using the LM3880 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.