HardLabs

Riscduino ATMEGA Adpater Rev1.0

dineshannayya·riscduino_board·KiCad_PCB/Riscduino_ATMEGA_Adpater_Rev1.0/Riscduino_ATMEGA_Adpater_Rev1.0.kicad_pcb

Riscduino ATMEGA Adpater Rev1.0 PCB layout, top view — open source AVR/Arduino board by dineshannayya
Simulate this board

About the Riscduino ATMEGA Adpater Rev1.0 PCB

Riscduino ATMEGA Adpater Rev1.0 is an open source AVR/Arduino PCB design by dineshannayya, published on GitHub. It is a 2-layer board measuring 88.7 × 27.6 mm, with 70 components from 23 distinct parts.

Its main chip is the ATMEGA8-16PU, from the AVR/Arduino family. Other key parts include the W25Q32JVSS, 23LC1024-I/P, Riscduino, LM1117MP-3.3 and LM1117S-ADJ. By type, the board carries 28 resistors, 21 capacitors, 7 ICs, 6 connectors, 5 diodes and 2 jumpers.

From the project

Riscduino PCB Board documentation

Main components on the Riscduino ATMEGA Adpater Rev1.0

ATMEGA8-16PUW25Q32JVSS23LC1024-I/PRiscduinoLM1117MP-3.3LM1117S-ADJ

Riscduino ATMEGA Adpater Rev1.0 bill of materials (BOM)

70 components, 23 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ATMEGA8-16PU
U1
2
W25Q32JVSS
U2, U4
1
23LC1024-I/P
U3
1
Riscduino
U5
1
LM1117MP-3.3
U6
1
LM1117S-ADJ
U7
1
ASE-10.000MHZ-LC-T
X1
1
Conn_01x03_Pin
J1
1
Conn_01x06
J2
4
Conn_01x01
J3, J6, J7, J8
2
Jumper_2
JP1, JP2
3
GREEN LED
D1, D4, D5
1
RED LED
D3
1
BLUE LED
D6
17
0.1uF
C1, C2, C4, C5, C6, C7, C8, C9 +9
2
10uF
C15, C21
2
22uF
C16, C22
1
R
R1
13
10K
R3, R4, R5, R6, R7, R22, R25, R26 +5
4
0E
R8, R9, R12, R13
Show 3 more
QtyPartRefs
3
DNI
R11, R18, R19
1
470 Ohm
R14
6
470 Ohm
R15, R16, R20, R21, R23, R24

Riscduino ATMEGA Adpater Rev1.0 design files

The KiCad project lives in the dineshannayya/riscduino_board repository on GitHub; these links point at the commit this page was built from.

Riscduino ATMEGA Adpater Rev1.0: common questions

What microcontroller does the Riscduino ATMEGA Adpater Rev1.0 use?

The Riscduino ATMEGA Adpater Rev1.0 is built around the ATMEGA8-16PU, from the AVR/Arduino family.

How big is the Riscduino ATMEGA Adpater Rev1.0 PCB?

The Riscduino ATMEGA Adpater Rev1.0 measures 88.7 × 27.6 mm, has 2 copper layers and is 1.61544 mm thick.

How many components are on the Riscduino ATMEGA Adpater Rev1.0?

70 components, from 23 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Riscduino ATMEGA Adpater Rev1.0 design files?

From the dineshannayya/riscduino_board repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Riscduino ATMEGA Adpater Rev1.0 design in my own project?

The repository has no license, so all rights stay with dineshannayya. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Riscduino ATMEGA Adpater Rev1.0 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in riscduino_board

Similar boards