Riscduino Tester
About the Riscduino Tester PCB
Riscduino Tester is an open source PCB design by dineshannayya, published on GitHub. It is a 2-layer board measuring 100.8 × 53.6 mm, with 88 components from 28 distinct parts.
Other key parts include the W25Q32JVSS, 23LC1024-I/P, LM1117MP-3.3, LM1117S-ADJ and CH340C. By type, the board carries 31 resistors, 27 capacitors, 14 connectors, 6 ICs, 5 diodes and 2 jumpers.
From the project
Riscduino PCB Board documentation
Main components on the Riscduino Tester
Riscduino Tester bill of materials (BOM)
88 components, 28 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | W25Q32JVSS | SOIC-8_5.23x5.23mm_P1.27mm | U1, U6 |
| 1 | 23LC1024-I/P | DIP-8_W7.62mm_LongPads | U2 |
| 1 | LM1117MP-3.3 | SOT-223-3_TabPin2 | U3 |
| 1 | LM1117S-ADJ | SOT-223-3_TabPin2 | U4 |
| 1 | CH340C | SOIC-16_3.9x9.9mm_P1.27mm | U5 |
| 1 | ASE-10.000MHZ-LC-T | Crystal_SMD_Abracon_ABM8G-4Pin_3.2x2.5mm | X1 |
| 1 | Conn_01x06_Pin | PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | ISP | PinHeader_2x03_P2.54mm_Vertical | J2 |
| 2 | Conn_01x08_Pin | PinHeader_1x08_P2.54mm_Vertical | J3, J9 |
| 4 | Conn_01x01 | PinHeader_1x01_P2.54mm_Vertical | J4, J5, J7, J12 |
| 1 | Conn_02x04_Odd_Even | PinHeader_2x04_P2.54mm_Vertical | J6 |
| 1 | USB_B_Micro | USB_Micro-B_Molex-105017-0001 | J8 |
| 1 | Conn_01x10_Pin | PinHeader_1x10_P2.54mm_Vertical | J10 |
| 1 | Conn_01x03_Pin | PinHeader_1x03_P2.54mm_Vertical | J11 |
| 2 | Conn_02x16_Odd_Even | PinHeader_2x16_P2.54mm_Vertical_Swap | J13, J14 |
| 2 | Jumper_2 | PinHeader_1x02_P2.54mm_Vertical | JP1, JP2 |
| 1 | 500 Ohm Trim Pot | Potentiometer_Bourns_3296W_Vertical | RV1 |
| 1 | 4Pin Round Button SPST Straight Tactile Switch SMD - TS4550TP | SW_SPST_EVPBF_TS4550TP | SW1 |
| 1 | BLUE LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 4 | GREEN LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2, D3, D4, D5 |
Show 8 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 21 | 0.1uf | C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C3, C5, C6, C7, C8, C9 +13 |
| 4 | 10uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4, C19, C20, C22 |
| 2 | 22uF | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C14, C21 |
| 7 | 0E | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R7, R8, R10, R17, R22, R28 |
| 14 | 10K | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2, R3, R4, R5, R6, R11, R16, R23 +6 |
| 2 | DNI | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R9, R14 |
| 1 | 0 Ohm | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R12 |
| 7 | 470 Ohm | R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R13, R15, R18, R19, R20, R21, R27 |
Riscduino Tester design files
The KiCad project lives in the dineshannayya/riscduino_board repository on GitHub; these links point at the commit this page was built from.
Riscduino Tester: common questions
How big is the Riscduino Tester PCB?
The Riscduino Tester measures 100.8 × 53.6 mm, has 2 copper layers and is 1.61544 mm thick.
How many components are on the Riscduino Tester?
88 components, from 28 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Riscduino Tester design files?
From the dineshannayya/riscduino_board repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Riscduino Tester design in my own project?
The repository has no license, so all rights stay with dineshannayya. Use it as a reference, and ask the author before reusing the design.
More boards in riscduino_board
Riscduino Fpga Rev1.1
104.3 × 63.6 mm101 parts2LNo license2
Riscduino Debug Rev1.4
81.7 × 63.6 mm95 parts2LNo license2
Riscduino Uno
68.8 × 53.6 mm90 parts2LNo license2
AVR/ArduinoRiscduino ATMEGA Adpater Rev1.0
88.7 × 27.6 mm70 parts2LNo license2
Riscduino Adpater Rev1.0
92.5 × 93.8 mm49 parts2LNo license2