Power mux usb bat
HeyPCB·power-kit·boards/power-mux/kicad/power_mux_usb_bat.kicad_pcb
About the Power mux usb bat PCB
Power mux usb bat is an open source PCB design by HeyPCB, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 28 × 32 mm, with 15 components from 12 distinct parts.
Other key parts include the TPS2116DRLR. By type, the board carries 6 resistors, 4 capacitors, 3 connectors, 1 IC and 1 diode.
It belongs with the power & battery designs in this gallery.
From the project
Six open power and charging boards: KiCad 10, JLCPCB-ready, CERN-OHL-S-2.0
USB-C first, a lithium cell as backup: a TPS2116 ideal-diode power mux with no diode drop and a pin that says which source is live.
Not fabricated, assembled or powered. Every number on this page is measured by KiCad 10 on the files in this folder; the full measurements are in report.json.
For a project that should keep running when the USB cable comes out: plug USB-C in and the load runs from USB; unplug it and a 1S cell on the JST PH connector takes over, with no Schottky drop and no current pushed back into either source. A TPS2116 in priority mode does the switching; the ST pin and a…

Main components on the Power mux usb bat
Power mux usb bat bill of materials (BOM)
15 components, 12 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TPS2116DRLR TPS2116 | SOT-583-8 | U1 |
| 1 | TYPE-C-31-M-12 USB-C | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | S2B-PH-K-S(LF)(SN) BATT | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J2 |
| 1 | PZ254V-11-04P OUT | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | KT-0603G Green (BATT) | LED_0603_1608Metric | D1 |
| 2 | CL21A106KAYNNNE 10uF | C_0805_2012Metric | C1, C4 |
| 2 | CL21B105KBFNNNE 1uF | C_0805_2012Metric | C2, C3 |
| 2 | 0402WGF5101TCE 5.1k | R_0402_1005Metric | R1, R2 |
| 1 | 0603WAF3302T5E 33k | R_0603_1608Metric | R3 |
| 1 | 0603WAF1002T5E 10k | R_0603_1608Metric | R4 |
| 1 | 0603WAF1003T5E 100k | R_0603_1608Metric | R5 |
| 1 | 0603WAF1001T5E 1k | R_0603_1608Metric | R6 |
Power mux usb bat design files
The KiCad project lives in the HeyPCB/power-kit repository on GitHub; these links point at the commit this page was built from.
Power mux usb bat: common questions
How big is the Power mux usb bat PCB?
The Power mux usb bat measures 28 × 32 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Power mux usb bat?
15 components, from 12 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Power mux usb bat design files?
From the HeyPCB/power-kit repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Power mux usb bat design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which HeyPCB chose for the repository.
More boards in power-kit
Similar boards
EinkPDA screen
TalismanDesign
95 × 54 mm27 parts2LApache-2.02.0kStack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kDisplay Carrier
AxxAxx
35.6 × 58.2 mm5 parts2LGPL-3.01.7kProgrammingAdapter
stuartpittaway
10.5 × 83 mm3 parts2LCC-BY-NC-4.01.1kTemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1kModule 16S PassiveBalanceAddOn
stuartpittaway
61 × 74 mm86 parts2LCC-BY-NC-4.01.1k