Temp sensor
juniper-garden·twig_temp_humidity_sensor
About the Temp sensor PCB
Temp sensor is an open source ESP32 PCB design by juniper-garden, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 48.2 × 24.9 mm, with 55 components from 35 distinct parts.
Its main chip is the ESP32-C3-MINI-1-H4, from the ESP32 family. Other key parts include the SHTC3, TLV62569DBVR, BME280, SI7020-A20 and SN65220DBVT. By type, the board carries 20 resistors, 11 capacitors, 7 ICs, 6 connectors, 2 switches and 2 diodes.
It belongs with the sensors designs in this gallery.
From the project
Hardware files for the temperature and humidity sensor
Main components on the Temp sensor
Temp sensor bill of materials (BOM)
55 components, 35 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-MINI-1-H4 ESP32-C3-MINI-1 | ESP32C3MINI1 | IC1 |
| 1 | SHTC3 | Sensirion_DFN-4-1EP_2x2mm_P1mm_EP0.7x1.6mm | U1 |
| 1 | TLV62569DBVR TLV62569DBV | SOT-23-5 | U2 |
| 1 | BME280 | Bosch_LGA-8_2.5x2.5mm_P0.65mm_ClockwisePinNumbering | U3 |
| 1 | SI7020-A20 MIC5365-3.3YC5 | SOT-353_SC-70-5 | U4 |
| 1 | SN65220DBVT SN65220 | SOT-23-6 | U5 |
| 1 | AS7341-DLGT | PSON80P310X200X110-8N | U6 |
| 1 | BC847BDW1T1G BC847BDW1 | SOT-363_SC-70-6 | Q1 |
| 1 | USB4105-GF-A USB_C_Receptacle_USB2.0 | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 3 | Conn_01x02_Male | PinHeader_1x02_P2.54mm_Vertical_SMD_Pin1Left | J2, J5, J6 |
| 1 | Conn_01x06_Male | PinHeader_1x07_P1.00mm_Vertical_SMD_Pin1Right | J3 |
| 1 | 105017-0001 USB_B_Micro | USB_Micro-B_Molex-105017-0001 | J4 |
| 3 | MountingHole | CorePin_1.15mm | H1, H2, H3 |
| 2 | TL6340AF160QG SW_Push_Right_Angle | SW_Push_1P1T-MP_NO_Horizontal_TL6340 | SW1, SW2 |
| 1 | SYM_Arrow_Normal | Sensor Keepout block | SYM1 |
| 1 | SYM_Arrow_Normal | LED Keepout block | SYM2 |
| 1 | SD03C-7 3.3v_TVS | D_SOD-323 | D1 |
| 1 | QLS6A-FKW-CNSNSF043 QLS6A | LED_Cree-PLCC6_4.7x1.5mm | D2 |
| 1 | MDMK4040T2R2MM 2.2uH | L_Taiyo-Yuden_MD-4040 | L2 |
| 5 | EMK105B7104KVHF 0.1u | C_0402_1005Metric | C1, C2, C4, C5, C10 |
Show 15 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | LMK212ABJ106MG-T 10u | C_1206_3216Metric_Pad1.42x1.75mm_HandSolder | C3, C9 |
| 1 | EMK105B7103KVHF 0.01u | C_0402_1005Metric | C6 |
| 1 | EMK107B7105KA-T 1u | C_0603_1608Metric | C7 |
| 1 | JMK107C6475KA-T 4.7u | C_0805_2012Metric | C8 |
| 1 | EMK105B7103KVHF 6.8p | C_0402_1005Metric | C11 |
| 2 | CR0603-FX-4990ELF 499R | R_0402_1005Metric | R1, R2 |
| 1 | CR0603-FX-2000ELF 200 | R_0402_1005Metric | R3 |
| 6 | ESR03EZPJ103 10K | R_0402_1005Metric | R4, R5, R7, R16, R17, R21 |
| 1 | ESR03EZPJ103 NP | R_0402_1005Metric | R6 |
| 1 | RC0603FR-13680KL 680k | R_0402_1005Metric | R8 |
| 1 | RC0603FR-07150KL 150K | R_0402_1005Metric | R9 |
| 2 | RC0603FR-1315KL 15K | R_0402_1005Metric | R10, R11 |
| 2 | RK73B1JTTDD270J 27 | R_0402_1005Metric | R12, R13 |
| 2 | RC0603JR-07100RL 100 | R_0402_1005Metric | R14, R15 |
| 2 | CR0603-FX-5101ELF 5.1k | R_0402_1005Metric | R19, R20 |
Temp sensor design files
The KiCad project lives in the juniper-garden/twig_temp_humidity_sensor repository on GitHub; these links point at the commit this page was built from.
- Layouttemp sensor.kicad_pcb
- Schematictemp sensor.kicad_sch
- BOMBOM/twig_0v3-BOM_JLCSMT.xlsx
Temp sensor: common questions
What microcontroller does the Temp sensor use?
The Temp sensor is built around the ESP32-C3-MINI-1-H4, from the ESP32 family.
How big is the Temp sensor PCB?
The Temp sensor measures 48.2 × 24.9 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Temp sensor?
55 components, from 35 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Temp sensor design files?
From the juniper-garden/twig_temp_humidity_sensor repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Temp sensor design in my own project?
Yes, under the terms of its GPL-3.0 license, which juniper-garden chose for the repository.
Can I test firmware for the Temp sensor without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in twig_temp_humidity_sensor
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k