Temp sensor panel
juniper-garden·twig_temp_humidity_sensor
About the Temp sensor panel PCB
Temp sensor panel is an open source ESP32 PCB design by juniper-garden, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 188.7 × 147.5 mm, with 40 components from 26 distinct parts.
Its main chip is the ESP32-C3-MINI-1, from the ESP32 family. Other key parts include the SHTC3, TLV62569DBV, BME280, SI7020-A20 and SN65220. By type, the board carries 16 resistors, 7 capacitors, 6 ICs, 5 connectors, 2 diodes and 2 inductors.
It belongs with the sensors designs in this gallery.
From the project
Hardware files for the temperature and humidity sensor
Main components on the Temp sensor panel
Temp sensor panel bill of materials (BOM)
40 components, 26 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-MINI-1 | ESP32C3MINI1 | IC1 |
| 1 | SHTC3 | Sensirion_DFN-4-1EP_2x2mm_P1mm_EP0.7x1.6mm | U1 |
| 1 | TLV62569DBV | SOT-23-5 | U2 |
| 1 | BME280 | Bosch_LGA-8_2.5x2.5mm_P0.65mm_ClockwisePinNumbering | U3 |
| 1 | SI7020-A20 Si7020-A20 | DFN-6-1EP_3x3mm_P1mm_EP1.5x2.4mm | U4 |
| 1 | SN65220 | SOT-23-6 | U5 |
| 1 | BC847BDW1 | SOT-363_SC-70-6 | Q1 |
| 3 | Conn_01x02_Male | PinHeader_1x02_P2.54mm_Vertical | J2, J5, J6 |
| 1 | Conn_01x05_Male | PinSocket_1x06_P1.00mm_Vertical_SMD_Pin1Right | J3 |
| 1 | USB_B_Micro | USB_Micro-B_Molex-105017-0001 | J4 |
| 1 | SW_Push | SW_Push_1P1T_NO_CK_KSC6xxJ | SW1 |
| 1 | 3.3V_TVS 3.3v_TVS | D_SOD-323_HandSoldering | D1 |
| 1 | QLS6A | LED_Cree-PLCC6_4.7x1.5mm | D2 |
| 1 | L_Core_Ferrite_Small | L_0603_1608Metric | L1 |
| 1 | 2.2UH 2.2uH | L_Taiyo-Yuden_MD-4040 | L2 |
| 4 | 0.1U 0.1u | C_0603_1608Metric | C1, C2, C4, C5 |
| 2 | 10U 10u | C_0805_2012Metric | C3, C9 |
| 1 | 4.7U 4.7u | C_0805_2012Metric | C8 |
| 2 | 499R | R_0603_1608Metric | R1, R2 |
| 1 | 200R 200 | R_0603_1608Metric | R3 |
Show 6 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 5 | 10K | R_0603_1608Metric | R4, R5, R7, R16, R17 |
| 1 | 680K 680k | R_0603_1608Metric | R8 |
| 1 | 150K | R_0603_1608Metric | R9 |
| 2 | 15K | R_0603_1608Metric | R10, R11 |
| 2 | 27R 27 | R_0603_1608Metric | R12, R13 |
| 2 | 100R 100 | R_0603_1608Metric | R14, R15 |
Temp sensor panel design files
The KiCad project lives in the juniper-garden/twig_temp_humidity_sensor repository on GitHub; these links point at the commit this page was built from.
Temp sensor panel: common questions
What microcontroller does the Temp sensor panel use?
The Temp sensor panel is built around the ESP32-C3-MINI-1, from the ESP32 family.
How big is the Temp sensor panel PCB?
The Temp sensor panel measures 188.7 × 147.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Temp sensor panel?
40 components, from 26 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Temp sensor panel design files?
From the juniper-garden/twig_temp_humidity_sensor repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Temp sensor panel design in my own project?
Yes, under the terms of its GPL-3.0 license, which juniper-garden chose for the repository.
Can I test firmware for the Temp sensor panel without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in twig_temp_humidity_sensor
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k