Before rescue

mitra42·frugal-iot-hw-sensor·claude-tools/layout/out/before_rescue.kicad_pcb

Before rescue PCB layout, top view — open source ESP32 board by mitra42

About the Before rescue PCB

Before rescue is an open source ESP32 PCB design by mitra42, published on GitHub. It is a 2-layer board measuring 64 × 37 mm, with 63 components from 36 distinct parts.

Its main chip is the ESP32-C3-WROOM-02U-N4, from the ESP32 family. Other key parts include the TP4056, XB5353A, ME6211C33M5G-N and SP3485EN-L/TR. By type, the board carries 23 resistors, 13 capacitors, 9 connectors, 5 ICs, 5 diodes and 4 jumpers.

It belongs with the iot & wireless and sensors designs in this gallery.

From the project

Reviewers can ignore this folder. Same method and scripts as ../../irrigation-layout-oct-2026/claude-tools/ (see its README for detail); everything runs on Mitra's Mac with KiCad 10. out/ folders are scratch.

Main components on the Before rescue

Before rescue bill of materials (BOM)

63 components, 36 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
TP4056
U1
1
XB5353A
U2
1
ME6211C33M5G-N
ME6211C33M5G
U3
1
ESP32-C3-WROOM-02U-N4
U4
1
SP3485EN-L/TR
SP3485EN
U5
2
AO3401A
Q1, Q2
1
TYPE-C-31-M-12
USB-C
J1
1
XY308-2.54-5P
J2 SENSORS 1-5
J2
1
XY308-2.54-5P
J3 RS485 1-5
J3
1
S2B-PH-K-S
CELL
J4
1
XY308-2.54-3P
GPIO10
J5
1
XY308-2.54-2P
5V IN (aux)
J6
1
EXT LED
J7
1
XY308-2.54-5P
J2 SENSORS 6-10
J12
1
XY308-2.54-5P
J3 SPARE 6-10
J13
1
500mA
JP1
1
A/RX
JP2
1
B/TX
JP3
1
TERM
JP4
1
TS-1187A-B-A-B
RESET
SW1
Show 16 more
QtyPartRefs
1
TS-1187A-B-A-B
BOOT
SW2
1
KT-0603R
RED
D1
2
KT-0805G
GREEN
D2, D4
1
SS34
D3
1
PSM712-LF-T7
PSM712
D5
5
10uF
C1, C2, C4, C5, C8
6
100nF
C3, C6, C9, C11, C12, C13
2
1uF
C7, C10
2
5.1k
R1, R2
6
4.7k
R3, R4, R16, R17, R18, R19
3
1k
R5, R6, R15
2
100k
R7, R10
2
1M
R8, R9
5
10k
R11, R12, R13, R14, R20
2
680R
R21, R22
1
120R
R23

Before rescue design files

The KiCad project lives in the mitra42/frugal-iot-hw-sensor repository on GitHub; these links point at the commit this page was built from.

Before rescue: common questions

What microcontroller does the Before rescue use?

The Before rescue is built around the ESP32-C3-WROOM-02U-N4, from the ESP32 family.

How big is the Before rescue PCB?

The Before rescue measures 64 × 37 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Before rescue?

63 components, from 36 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Before rescue design files?

From the mitra42/frugal-iot-hw-sensor repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the Before rescue design in my own project?

The repository has no license, so all rights stay with mitra42. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Before rescue without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in frugal-iot-hw-sensor

Similar boards