Dew control

ncleesattel·ESP32_DewHeater·hardware/dew_control_pcb/dew_control_pcb.kicad_pcb

Dew control PCB layout, top view — open source ESP32 board by ncleesattel

About the Dew control PCB

Dew control is an open source ESP32 PCB design by ncleesattel, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 130 × 120 mm, with 77 components from 34 distinct parts.

Its main chip is the ESP32-30PIN, from the ESP32 family. Other key parts include the L78M05ABDT, BME280 and ACS712XLCTR-05B. By type, the board carries 32 resistors, 16 capacitors, 11 connectors, 6 ICs, 4 diodes and 3 transistors.

It belongs with the sensors and displays & leds designs in this gallery.

From the project

ESP32 open-loop dew heater

Best case 170 Eur if you can share all pcbs Worst case 320 Eur if you keep all pcbs and build only one

Dew control, from the project README
From the project README

Main components on the Dew control

Dew control bill of materials (BOM)

77 components, 34 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-30PIN
ESP32-30pin
IC1
1
L78M05ABDT
L78M05ABDT-TR
U1
1
BME280
U2
3
ACS712XLCTR-05B
ACS712xLCTR-05B
U3, U4, U5
3
NTMFS5C670NLT1G
Q1, Q2, Q3
1
C160355
POWER
J1
1
C160355
ON/OFF
J2
1
C492552
RSA DEW
J3
1
5V
J4
1
C239334
CURRENT EN
J5
1
C157919
OLED
J11
1
I2C
J12
1
GND
J13
1
3V3
J14
1
PROBE1
J31
1
PROBE1
PROBE2
J32
1
C206887
Fuse
F1
1
EN I2C Mode
JP1
1
I2C Adress
JP2
2
C470754
RotaryEncoder_Switch
SW1, SW2
Show 14 more
QtyPartRefs
1
S10MC
D1
3
C8678
D_Schottky
D2, D3, D4
6
0.1UF
0.1uF
C1, C4, C6, C7, C11, C13
1
0.33UF
0.33uF
C2
1
470UF
470uF
C3
1
100UF
100uF
C5
3
1NF
1nF
C8, C12, C14
4
0.01UF
0.01uF
C9, C10, C15, C16
3
150
R1, R2, R5
16
10K
R3, R4, R6, R7, R8, R9, R10, R13 +8
6
4K7
R11, R12, R15, R16, R20, R21
1
1.5K
R22
3
15K
R23, R25, R27
3
43K
43k
R24, R26, R28

Dew control design files

The KiCad project lives in the ncleesattel/ESP32_DewHeater repository on GitHub; these links point at the commit this page was built from.

Dew control: common questions

What microcontroller does the Dew control use?

The Dew control is built around the ESP32-30PIN, from the ESP32 family.

How big is the Dew control PCB?

The Dew control measures 130 × 120 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Dew control?

77 components, from 34 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Dew control design files?

From the ncleesattel/ESP32_DewHeater repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Dew control design in my own project?

Yes, under the terms of its GPL-3.0 license, which ncleesattel chose for the repository.

Can I test firmware for the Dew control without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in ESP32_DewHeater

Similar boards