Home health care
nguyen-van-phuong-19·Home_health_care·Design/wearable_device/wearable_device.kicad_pcb
About the Home health care PCB
Home health care is an open source ESP32 PCB design by nguyen-van-phuong-19, published on GitHub. It is a 4-layer board measuring 50 × 41.3 mm, with 49 components from 22 distinct parts.
Its main chip is the ESP32-S3-MINI-1, from the ESP32 family. Other key parts include the L80-R, LP2985-33DBVR, TP4056, LIS2DH12TR and CH340C. By type, the board carries 16 resistors, 15 capacitors, 7 connectors, 6 ICs, 4 transistors and 1 switch.
It belongs with the wearables designs in this gallery.
Main components on the Home health care
Home health care bill of materials (BOM)
49 components, 22 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-MINI-1 | ESP32-S2-MINI-1 | U1 |
| 1 | L80-R | XCVR_L80-R | U2 |
| 1 | LP2985-33DBVR | SOT95P280X145-5N | U3 |
| 1 | TP4056 | SOP127P600X175-9N | U4 |
| 1 | LIS2DH12TR | PQFN50P200X200100-12N | U5 |
| 1 | CH340C | SOIC-16_3.9x9.9mm_P1.27mm | U6 |
| 2 | BSS138 | SOT-23 | Q1, Q2 |
| 2 | BC817 | SOT-23 | Q3, Q5 |
| 1 | Micro_SD_Card | microSD_HC_Hirose_DM3D-SF | J1 |
| 1 | POWER | PinHeader_1x01_P2.00mm_Vertical | J2 |
| 2 | Conn_01x04_Pin | PinHeader_1x04_P2.00mm_Vertical | J3, J4 |
| 1 | Conn_01x07_Pin | PinHeader_1x07_P2.54mm_Vertical | J5 |
| 1 | GND | PinHeader_1x01_P2.00mm_Vertical | J6 |
| 1 | USB_C_Plug_USB2.0 | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | P1 |
| 1 | SW_Push | SW_Tactile_SPST_NO_Straight_CK_PTS636Sx25SMTRLFS | SW1 |
| 8 | 10uF | C_0603_1608Metric | C1, C2, C3, C6, C8, C13, C14, C17 |
| 4 | 0.1uF | C_0603_1608Metric | C4, C5, C7, C9 |
| 1 | 10nF | C_0603_1608Metric | C12 |
| 2 | 100nF | C_0603_1608Metric | C15, C16 |
| 13 | 10k | R_0603_1608Metric | R1, R2, R4, R5, R6, R7, R10, R11 +5 |
Show 2 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 1.2k | R_0603_1608Metric | R3 |
| 2 | 4.7k | R_0603_1608Metric | R8, R9 |
Home health care design files
The KiCad project lives in the nguyen-van-phuong-19/Home_health_care repository on GitHub; these links point at the commit this page was built from.
Home health care: common questions
What microcontroller does the Home health care use?
The Home health care is built around the ESP32-S3-MINI-1, from the ESP32 family.
How big is the Home health care PCB?
The Home health care measures 50 × 41.3 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Home health care?
49 components, from 22 distinct parts. The full bill of materials is listed on this page.
Where can I download the Home health care design files?
From the nguyen-van-phuong-19/Home_health_care repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Home health care design in my own project?
The repository has no license, so all rights stay with nguyen-van-phuong-19. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Home health care without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k