Proto amp bodge board
About the Proto amp bodge board
Proto amp bodge board is an open source PCB design by PantsForBirds, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 13 × 13 mm, with 6 components from 5 distinct parts.
Other key parts include the OPA358AIDCKR. By type, the board carries 3 resistors, 2 capacitors and 1 IC.
It belongs with the rf & radio and dev boards & breakouts designs in this gallery.
From the project
Open Source Embedded ADS-B Receiver
ADSBee is a family of open-source, dual-band ADS-B receivers from Pants for Birds LLC. Every ADSBee decodes 1090 MHz Mode S / ADS-B and 978 MHz UAT transmissions onboard — no SDR dongle, FPGA, or host computer required — maintains an aircraft dictionary, and streams tracked aircraft over UART (and, on the 1090 family, WiFi / Ethernet) in a wide range of output protocols. This repository holds the firmware, hardware design files, datasheets, and host software for the whole family.
Main components on the Proto amp bodge board
Proto amp bodge board bill of materials (BOM)
6 components, 5 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | OPA358AIDCKR | SOT-363_SC-70-6 | U1 |
| 1 | 0.1uF | C_0402_1005Metric | C1 |
| 1 | 22nF | C_0402_1005Metric | C2 |
| 2 | 10k | R_0402_1005Metric | R1, R2 |
| 1 | 100k | R_0402_1005Metric | R3 |
Proto amp bodge board design files
The KiCad project lives in the PantsForBirds/adsbee repository on GitHub; these links point at the commit this page was built from.
Proto amp bodge board: common questions
How big is the Proto amp bodge board?
The Proto amp bodge board measures 13 × 13 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Proto amp bodge board?
6 components, from 5 distinct parts. The full bill of materials is listed on this page.
Where can I download the Proto amp bodge board design files?
From the PantsForBirds/adsbee repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Proto amp bodge board design in my own project?
Yes, under the terms of its GPL-3.0 license, which PantsForBirds chose for the repository.
More boards in adsbee
RF Detector Board
28 × 44 mm24 parts2LGPL-3.0322
RP2040/RP2350Proto ads bee mcu board
55 × 58 mm20 parts2LGPL-3.0322
Proto ads bee rf board
44 × 28 mm16 parts2LGPL-3.0322
Panel proto data slicer board
56 × 37.5 mm13 parts2LGPL-3.0322
Proto data slicer board
14 × 12.5 mm13 parts2LGPL-3.0322
Panel proto lna board
69 × 44 mm12 parts2LGPL-3.0322
Proto lna board
23 × 11 mm12 parts2LGPL-3.0322
Panel proto tracking comparator board
68 × 45 mm8 parts2LGPL-3.0322
Proto ufl match board
23 × 8 mm7 parts2LGPL-3.0322
Proto ufl pi board
19 × 8 mm5 parts2LGPL-3.0322
Panel saw eval board
57 × 44 mm3 parts2LGPL-3.0322
Similar boards
88 Pin Vag Breakout
rusefi
142 × 58 mm91 parts2LGPL-3.01.2k
134pin 7-967288-1
139.7 × 73.7 mm38 parts2LGPL-3.01.2k
Breakout 60pin EEC-IV
139.7 × 62.2 mm15 parts2LGPL-3.01.2k
Breakout 112pin Connector
174 × 58 mm39 parts2LGPL-3.01.2k
Eecv breakout
140.8 × 53.7 mm9 parts4LGPL-3.01.2k
Rj45 breakout
rene-dev
15.2 × 53.8 mm3 parts2LGPL-3.0979