10 open source boards using the NodeMCU1.0(ESP-12E)
Real designs built with the NodeMCU1.0(ESP-12E), from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP8266
Documentation
Biomicrosystems
105 × 72 mm28 parts2LNo license2ESP8266
Window curtain alarm
timbleman
99.1 × 62.2 mm21 parts2LNo license1ESP8266
Light
zeyad-hisham-cyper
161.4 × 165.1 mm76 parts2LMIT0ESP8266
Window roller shutter control
Kriechi
91.4 × 185.4 mm43 parts2LMIT0ESP8266
ControlUnitInput
spotlesscoder
96.1 × 90.1 mm43 parts2LCERN-OHL-1.20ESP8266
Diploma Work
MihaelaGadzhalova707
57.4 × 108.2 mm40 parts2LNo license0ESP8266
MCT19
ZeniteSolar
42.8 × 83.8 mm24 parts2LGPL-3.00ESP8266
IoT-temp based fan speed controller
LudoProvost
52 × 56 mm10 parts2LNo license0ESP8266
ButtonLEDsController
spotlesscoder
94 × 90 mm39 parts2LCERN-OHL-1.20ESP8266
RGB Treppe
SmartHome-yourself
72.4 × 74.9 mm16 parts2LGPL-2.06
How designs wire the NodeMCU1.0(ESP-12E)
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the NodeMCU1.0(ESP-12E) connects to, and the resistors, capacitors and other passives placed on it.
- The RSV pins is left unconnected on 83% of them (a signal on 3).
- The SD3(GPIO10) pin is left unconnected on 7 of 9 designs (a signal on 2).
- The SD2(GPIO9) pin is left unconnected on 7 of 9 designs (a signal on 2).
- The SD1(MOSI) pin is left unconnected on 6 of 9 designs (a signal on 3).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| RSVpin 2, 3 | Connected to: Not connected 83% · a signal 17% | — |
| SD3(GPIO10)pin 4 | Connected to: Not connected 78% · a signal 22% | — |
| SD2(GPIO9)pin 5 | Connected to: Not connected 78% · a signal 22% | — |
| SD1(MOSI)pin 6 | Connected to: Not connected 67% · a signal 33% | — |
| CMD(CS)pin 7 | Connected to: Not connected 67% · a signal 33% | — |
| SDO(MISO)pin 8 | Connected to: Not connected 67% · a signal 33% | — |
| CLK(SCLK)pin 9 | Connected to: Not connected 67% · a signal 33% | — |
| GNDpin 10, 14, 17, 24 | Connected to: GND 69% · not connected 31% | — |
| ENpin 12 | Connected to: Not connected 67% · a signal 33% | — |
| RSTpin 13 | Connected to: Not connected 67% · a signal 33% | — |
| VINpin 15 | Connected to: 5V 78% · a signal 22% | — |
| TX(GPIO1)pin 18 | Connected to: Not connected 67% · a signal 33% | — |
| RX(DPIO3)pin 19 | Connected to: Not connected 67% · a signal 33% | — |
| D6(GPIO12)pin 22 | Connected to: A connector 56% |
|
| D0(GPIO16)pin 30 | Connected to: A connector 44% |
|
9 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include RGB Treppe by SmartHome-yourself, Documentation by Biomicrosystems, Window curtain alarm by timbleman and Window roller shutter control by Kriechi.
The NodeMCU1.0(ESP-12E) in open source designs
The gallery holds 10 open source boards using the NodeMCU1.0(ESP-12E) from 9 GitHub repositories; a typical one measures about 92.7 × 86.9 mm and carries around 34 components.
100% are two-layer designs, the rest use four layers or more, and 60% carry an open source license.
The most starred is RGB Treppe by SmartHome-yourself.
Parts used alongside the NodeMCU1.0(ESP-12E)
Microcontrollers on boards using the NodeMCU1.0(ESP-12E)
What boards using the NodeMCU1.0(ESP-12E) are built for
NodeMCU1.0(ESP-12E): common questions
Where can I find a NodeMCU1.0(ESP-12E) reference design?
Each of the 10 boards on this page is a real design using the NodeMCU1.0(ESP-12E). Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the NodeMCU1.0(ESP-12E) RSV pin connected?
The RSV pins is left unconnected on 83% of them (a signal on 3). Counted from the KiCad layouts of 9 open source designs using the NodeMCU1.0(ESP-12E).
How is the NodeMCU1.0(ESP-12E) SD3(GPIO10) pin connected?
The SD3(GPIO10) pin is left unconnected on 7 of 9 designs (a signal on 2). Counted from the KiCad layouts of 9 open source designs using the NodeMCU1.0(ESP-12E).
How is the NodeMCU1.0(ESP-12E) SD2(GPIO9) pin connected?
The SD2(GPIO9) pin is left unconnected on 7 of 9 designs (a signal on 2). Counted from the KiCad layouts of 9 open source designs using the NodeMCU1.0(ESP-12E).
Which microcontrollers do boards using the NodeMCU1.0(ESP-12E) use?
Most are built on ESP8266 (10).
How big is a typical board using the NodeMCU1.0(ESP-12E)?
The median is 92.7 × 86.9 mm, and 100% are two-layer designs.
What is the most popular open source board using the NodeMCU1.0(ESP-12E)?
By GitHub stars, RGB Treppe by SmartHome-yourself, with 6 stars.
Can I simulate one of these boards using the NodeMCU1.0(ESP-12E) before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.