Haptic-Glove

ZharbolatDinmukhamed·Haptic-Glove-PCB

Haptic-Glove PCB layout, top view — open source ESP32 board by ZharbolatDinmukhamed

About the Haptic-Glove PCB

Haptic-Glove is an open source ESP32 PCB design by ZharbolatDinmukhamed, published on GitHub. It is a 4-layer board measuring 62 × 46.9 mm, with 108 components from 49 distinct parts.

Its main chip is the ESP32-S3, from the ESP32 family. Other key parts include the ESP-PSRAM64H, MAX98357A, DRV8833PW, W25Q128JVS and TP4056-42-ESOP8. By type, the board carries 37 capacitors, 29 resistors, 11 diodes, 9 ICs, 8 transistors and 4 inductors.

It belongs with the robotics & motion designs in this gallery.

From the project

A wrist-mounted PCB for a haptic feedback glove, developed as part of my Research Assistantship at the Tactile Laboratory, Nazarbayev University.

Main components on the Haptic-Glove

Haptic-Glove bill of materials (BOM)

108 components, 49 distinct parts.

QtyPartRefs
1
ESP-PSRAM64H
IC1
1
MAX98357A
U1
1
DRV8833PW
U2
1
ESP32-S3
U3
1
W25Q128JVS
U4
1
TP4056-42-ESOP8
U5
1
XC6220B331MR
U6
1
LIS2HH12
U7
1
DW01A
U8
5
SS8050
Q1, Q2, Q3, Q4, Q5
1
AO3401A
Q6
1
MMBT3904
Q7
1
FS8205A
Q8
1
ECS-2520MV-xxx-xx
Y1
1
TYPE-C-31-M-12
J2
1
Conn_01x04
J3
1
Conn_01x02
J4
1
PCB Antenna 2.4GHz 50Ohm
ANT1
1
Speaker
LS1
1
INMP441ACEZ-R7
MK1
Show 29 more
QtyPartRefs
2
SW_Push
SW1, SW2
1
SW_DPDT_x2
SW3
5
1N4148W
D1, D2, D3, D4, D5
1
USBLC6-2SC6
STMicroelectronics
D6
1
LED_GRN
D7
1
LED_RED
D8
2
SS14
D9, D10
1
LED
D11
2
*
FB0402
*
FB1, FB2
2
2n2
L1, L2
21
100n
C1, C2, C3, C4, C5, C7, C9, C10 +13
10
10u
C6, C14, C17, C25, C27, C30, C31, C32 +2
2
220p
C8, C11
1
10p
C16
1
2u2
C20
2
3p3
C22, C24
3
100k
R1, R18, R21
1
634K
R2
7
1k
R3, R4, R5, R8, R9, R28, R29
6
5k1
R6, R7, R10, R12, R14, R15
2
200m
R11, R13
1
22R
R16
1
220k
R17
2
10k
R19, R26
2
1k3
R20, R22
1
220
R23
1
1k4
R24
1
27k
R25
1
100
R27

Haptic-Glove design files

The KiCad project lives in the ZharbolatDinmukhamed/Haptic-Glove-PCB repository on GitHub; these links point at the commit this page was built from.

Haptic-Glove: common questions

What microcontroller does the Haptic-Glove use?

The Haptic-Glove is built around the ESP32-S3, from the ESP32 family.

How big is the Haptic-Glove PCB?

The Haptic-Glove measures 62 × 46.9 mm, has 4 copper layers and is 1.58 mm thick.

How many components are on the Haptic-Glove?

108 components, from 49 distinct parts. The full bill of materials is listed on this page.

Where can I download the Haptic-Glove design files?

From the ZharbolatDinmukhamed/Haptic-Glove-PCB repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Haptic-Glove design in my own project?

The repository has no license, so all rights stay with ZharbolatDinmukhamed. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Haptic-Glove without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards