Weatherframe

amselgesang·weatherframe_v01·hardware/kicad/weatherframe/weatherframe.kicad_pcb

Weatherframe PCB layout, top view — open source ESP32 board by amselgesang

About the Weatherframe PCB

Weatherframe is an open source ESP32 PCB design by amselgesang, published on GitHub under the MIT license. It is a 2-layer board measuring 64 × 46 mm, with 46 components from 30 distinct parts.

Its main chip is the ESP32-S3-WROOM-1-N16R8, from the ESP32 family. Other key parts include the MCP73831T-2ACI/OT, TPS63001DRCR, SHT40-AD1B-R2 and USBLC6-2SC6. By type, the board carries 16 resistors, 13 capacitors, 5 ICs, 4 switches, 3 connectors and 2 transistors.

It belongs with the iot & wireless, displays & leds and power & battery designs in this gallery.

From the project

My weather station hardver

A wall-hung weather station in a picture frame: Waveshare 7.5" e-paper (800 × 480, 4-level grayscale), custom ESP32-S3 board with a rechargeable 1S LiPo, Wi-Fi + Open-Meteo. Wakes every 15 minutes, refreshes the display, sleeps. Charges over USB-C.

The VBUS-sense (GPIO4) and charger-STAT (GPIO15) dividers were 100 k/100 k: 5 V → 2.5 V, which sits exactly on the ESP32-S3's VIH minimum (0.75 × 3.3 V = 2.475 V) and reads undefined on a 4.75 V USB supply. With 150 k on the bottom they give 3.0 V (2.85–3.15 V over the USB range), still below the 3.6 V absolute maximum. Changed in gen/design.py…

Main components on the Weatherframe

Weatherframe bill of materials (BOM)

46 components, 30 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-S3-WROOM-1-N16R8
U1
1
MCP73831T-2ACI/OT
MCP73831-2
U2
1
TPS63001DRCR
TPS63001
U3
1
SHT40-AD1B-R2
SHT40-AD1B
U4
1
USBLC6-2SC6
U5
2
AO3401A
Q1, Q2
1
TYPE-C-31-M-12
USB-C
J1
1
PH-2AWT (JST PH 2.0)
LiPo 1S
J2
1
1x9 pin header 2.54 mm (hand-solder)
E-Paper HAT
J3
1
TS-1187A-B-A-B
RESET
SW1
1
TS-1187A-B-A-B
BOOT
SW2
1
TS-1187A-B-A-B
REFRESH
SW3
1
MSK12C02
MAINT
SW4
1
B5819W
D1
1
KT-0603R
CHG
D2
1
SWPA4030S1R5NT
1.5uH
L1
3
4.7uF
C1, C2, C13
5
100nF
C3, C5, C9, C11, C12
1
10uF
C4
2
22uF
C6, C7
Show 10 more
QtyPartRefs
1
10uF
C8
1
1uF
C10
2
5.1k
R1, R2
1
2k
R3
1
1k
R4
3
100k
R5, R10, R17
2
100k
150k
R6, R11
2
1M
R8, R9
3
10k
R12, R13, R14
2
4.7k
R15, R16

Weatherframe design files

The KiCad project lives in the amselgesang/weatherframe_v01 repository on GitHub; these links point at the commit this page was built from.

Weatherframe: common questions

What microcontroller does the Weatherframe use?

The Weatherframe is built around the ESP32-S3-WROOM-1-N16R8, from the ESP32 family.

How big is the Weatherframe PCB?

The Weatherframe measures 64 × 46 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Weatherframe?

46 components, from 30 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Weatherframe design files?

From the amselgesang/weatherframe_v01 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Weatherframe design in my own project?

Yes, under the terms of its MIT license, which amselgesang chose for the repository.

Can I test firmware for the Weatherframe without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in weatherframe_v01

Similar boards