21 open source boards using the 74HC123
Real designs built with the 74HC123, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Internal sdcard interface
ifilot
219 × 88 mm77 parts2LNo license3Isa sdcard
ifilot
104.4 × 82.7 mm46 parts4LNo license1EVD80 MCU
Alexandr-Filatov
236 × 150 mm746 parts6LNo license0Valhalla MOD XVR(4IO)
csdexter
99.6 × 99.6 mm128 parts2LGPL-3.00Counting pru
lnls-sirius
160 × 100 mm92 parts2LNo license0RP2040/RP2350
Titanrio
ggarciabaez
220.5 × 164.5 mm81 parts4LNo license0Isouart4
nedko
89 × 99 mm81 parts2LNo license0AVR/Arduino
Multicartridge smd-32u4-front dipswitch
ifilot
80 × 100 mm72 parts2LNo license0Project - VRMS
lnls-sirius
126 × 100 mm60 parts2LNo license0- schematic only · 52 parts
Thermomix tm31-power board
junado
52 partsCC-BY-SA-4.00 MegaAV rev0.5
RIP-Felix
50 × 50 mm143 parts4LCERN-OHL-S-2.049Philips P2000T SD-CARD SLOT2 cartridge
ifilot
85.1 × 100 mm62 parts4LNo license3Prototype
ifilot
151.6 × 82.7 mm45 parts2LNo license1Serienplan
stonedDiscord
107.1 × 235.8 mm171 parts2LNo license0P2000t multicartridge smd
ifilot
80 × 100.3 mm24 parts2LNo license0Sdcard prototype
ifilot
82.6 × 67.3 mm34 parts2LNo license3Multicartridge smd top dipswitch
ifilot
80 × 100 mm23 parts2LNo license0ESP32
D34-ctrl unrouted
aquarat
81 × 47 mm45 parts2LCustom license0Multicartridge sst39sf010-topbutton
ifilot
80 × 105.4 mm20 parts2LNo license0P2000t multicartridge
ifilot
80 × 100 mm15 parts2LNo license0P2000t multicartridge zif
ifilot
80 × 100 mm15 parts2LNo license0
How designs wire the 74HC123
Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the 74HC123 connects to, and the resistors, capacitors and other passives placed on it.
- The RCEXT pins have a pull-up to 5V on 9 of 12 designs, most often 10 kΩ (then 470 kΩ).
- The CEXT pins have a series capacitor on 8 of 12 designs, most often 1 µF (then 10 nF).
- The RCEXT pins have a series capacitor on 7 of 12 designs, most often 1 µF (then 10 nF).
- The VCC pin has a decoupling capacitor on 6 of 11 designs, most often 100 nF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Qpin 4, 5, 12, 13 | Connected to: Signal 63% · not connected 38% |
|
| CEXTpin 6, 14 | Connected to: Signal 79% |
|
| RCEXTpin 7, 15 | Connected to: Signal 96% |
|
| GNDpin 8 | Connected to: GND 83% · a signal 17% | — |
| VCCpin 16 | Connected to: 5V 91% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MegaAV rev0.5 by RIP-Felix, Internal sdcard interface by ifilot, Isa sdcard by ifilot and EVD80 MCU PCB by Alexandr-Filatov.
The 74HC123 in open source designs
The gallery holds 21 open source boards using the 74HC123 from 13 GitHub repositories; a typical one measures about 87 × 100 mm and carries around 60 components.
75% are two-layer designs, the rest use four layers or more, and 14% carry an open source license.
The most starred is MegaAV rev0.5 by RIP-Felix.
Parts used alongside the 74HC123
Microcontrollers on boards using the 74HC123
What boards using the 74HC123 are built for
74HC123: common questions
Where can I find a 74HC123 reference design?
Each of the 21 boards on this page is a real design using the 74HC123. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the 74HC123 RCEXT pin?
The RCEXT pins have a pull-up to 5V on 9 of 12 designs, most often 10 kΩ (then 470 kΩ). Counted from the KiCad layouts of 12 open source designs using the 74HC123.
How is the 74HC123 CEXT pin connected?
The CEXT pins have a series capacitor on 8 of 12 designs, most often 1 µF (then 10 nF). Counted from the KiCad layouts of 12 open source designs using the 74HC123.
What decoupling capacitors do designs use on the 74HC123 VCC pin?
The VCC pin has a decoupling capacitor on 6 of 11 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 12 open source designs using the 74HC123.
What parts are used alongside the 74HC123?
The 74HC00, 74HC165, 74HC32, 74HC74 and 74HC138 appear in the most repositories here.
Which microcontrollers do boards using the 74HC123 use?
Most are built on AVR/Arduino (1), ESP32 (1) and RP2040/RP2350 (1).
How big is a typical board using the 74HC123?
The median is 87 × 100 mm, and 75% are two-layer designs.
What is the most popular open source board using the 74HC123?
By GitHub stars, MegaAV rev0.5 by RIP-Felix, with 49 stars.
Can I simulate one of these boards using the 74HC123 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.