AX12 Teensy V1
About the AX12 Teensy V1 PCB
AX12 Teensy V1 is an open source NXP PCB design by AREA-Amiens, published on GitHub. It is a 2-layer board measuring 60 × 41.4 mm, with 20 components from 15 distinct parts.
Its main chip is the TEENSY3.2, from the NXP family. Other key parts include the SN65HVD232. By type, the board carries 8 connectors, 4 capacitors, 3 resistors, 2 ICs, 2 diodes and 1 jumper.
From the project
Hardware for AREA.old boards
Main components on the AX12 Teensy V1
AX12 Teensy V1 bill of materials (BOM)
20 components, 15 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TEENSY3.2 | TEENSY32 | IC1 |
| 1 | SN65HVD232 | SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | uart | PinHeader_1x04_P2.54mm_Vertical | J1 |
| 4 | AX12 | Molex_SPOX_5267-03A_1x03_P2.50mm_Vertical | J2, J3, J4, J5 |
| 1 | 12VP | Wuerth_3.96mm_2pin_645002114822 | J8 |
| 2 | Conn_CAN | 690367290476 | J9, J10 |
| 1 | 120 | PinHeader_1x02_P2.54mm_Vertical | JP1 |
| 1 | LED_12V | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 1 | TVS | SOT-23 | D2 |
| 2 | 100n | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C4 |
| 1 | 100u | CP_Radial_D8.0mm_P3.50mm | C2 |
| 1 | 10u | CP_Radial_D4.0mm_P2.00mm | C3 |
| 1 | 1.5K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 2k | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 1 | 120 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3 |
AX12 Teensy V1 design files
The KiCad project lives in the AREA-Amiens/AREA.old-boards-hardware repository on GitHub; these links point at the commit this page was built from.
AX12 Teensy V1: common questions
What microcontroller does the AX12 Teensy V1 use?
The AX12 Teensy V1 is built around the TEENSY3.2, from the NXP family.
How big is the AX12 Teensy V1 PCB?
The AX12 Teensy V1 measures 60 × 41.4 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the AX12 Teensy V1?
20 components, from 15 distinct parts. The full bill of materials is listed on this page.
Where can I download the AX12 Teensy V1 design files?
From the AREA-Amiens/AREA.old-boards-hardware repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the AX12 Teensy V1 design in my own project?
The repository has no license, so all rights stay with AREA-Amiens. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the AX12 Teensy V1 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug NXP firmware against it before you order a PCB.
More boards in AREA.old-boards-hardware
STM32PCB Pompe V2
89.8 × 59.3 mm193 parts2LNo license0
STM32IO Board V1
79 × 49.5 mm88 parts2LNo license0
Carte Alim V4
111.1 × 60 mm57 parts2LNo license0
STM32Sensor v2-board
55.3 × 46 mm47 parts2LNo license0
ESP32PCB ESP32 CAN
52.2 × 67.2 mm47 parts2LNo license0
NXPCarte Principale
80 × 65 mm44 partsNo license0
STM32Rmeasure V1 Board
58 × 28.5 mm43 partsNo license0
NXPGatling-V2-board
65 × 45 mm28 parts2LNo license0
NXPLidar-V2-board
54.8 × 29 mm15 parts2LNo license0
Similar boards
NXP32Bit shift register
MaltWhiskey
100 × 54 mm56 parts4LNo license763
NXPMega-Cube-Board
200 × 54 mm100 parts4LNo license763
NXPMCL64
MicroCoreLabs
39.3 × 61.8 mm9 parts4LNo license532
NXPROM Emulator
21.5 × 37.1 mm5 parts2LNo license532
NXPMCLZ8
37.1 × 61.5 mm6 parts4LNo license532
NXPXTMAX
81 × 46 mm14 parts4LNo license532