58 open source boards using the SN65HVD232

Real designs built with the SN65HVD232, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

58 boardsClear filters|Most starred

How designs wire the SN65HVD232

Read from the KiCad layouts of 30 open source designs, one per repository: what each pin of the SN65HVD232 connects to, and the resistors, capacitors and other passives placed on it.

  • The VCC pin has a decoupling capacitor on 25 of 30 designs, most often 100 nF (then 2.2 µF).
  • The CANL pin has a series resistor on 22 of 30 designs, most often 120 Ω (then 60 Ω).
  • The CANH pin has a series resistor on 22 of 30 designs, most often 120 Ω (then 60 Ω).
GNDpin 2Connected to: GND 100%
VCCpin 3Connected to: 3.3V 97%
  • Decoupling capacitor on 83% · 100 nF (18), 2.2 µF (15), 1 µF (3)
NCpin 5, 8Connected to: Not connected 82% · a signal 18%
  • Resistor to GND on 37% · 10 kΩ (10), 33 kΩ (1)
CANLpin 6Connected to: A connector 90%
  • Series resistor on 73% · 120 Ω (10), 60 Ω (2), 0 Ω (1)
CANHpin 7Connected to: A connector 90%
  • Series resistor on 73% · 120 Ω (11), 60 Ω (2), 62 Ω (1)

2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Bldc by mrkindustries, QuadcopterSystem by vedderb, CAN motor controller by wjklimek1 and Coonix by TreeNewbeer.

The SN65HVD232 in open source designs

The gallery holds 58 open source boards using the SN65HVD232 from 30 GitHub repositories; a typical one measures about 70.8 × 65 mm and carries around 102 components.

64% are two-layer designs, the rest use four layers or more, and 26% carry an open source license.

The most starred is Bldc by mrkindustries.

Microcontrollers on boards using the SN65HVD232

SN65HVD232: common questions

Where can I find a SN65HVD232 reference design?

Each of the 58 boards on this page is a real design using the SN65HVD232. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the SN65HVD232 VCC pin?

The VCC pin has a decoupling capacitor on 25 of 30 designs, most often 100 nF (then 2.2 µF). Counted from the KiCad layouts of 30 open source designs using the SN65HVD232.

What resistor goes on the SN65HVD232 CANL pin?

The CANL pin has a series resistor on 22 of 30 designs, most often 120 Ω (then 60 Ω). Counted from the KiCad layouts of 30 open source designs using the SN65HVD232.

What resistor goes on the SN65HVD232 CANH pin?

The CANH pin has a series resistor on 22 of 30 designs, most often 120 Ω (then 60 Ω). Counted from the KiCad layouts of 30 open source designs using the SN65HVD232.

What parts are used alongside the SN65HVD232?

The STM32F40X_LQFP64, DRV8302, TC2117, ESP32-WROOM-32 and USBLC6-2SC6 appear in the most repositories here.

Which microcontrollers do boards using the SN65HVD232 use?

Most are built on STM32 (35), ESP32 (11), NXP (6) and ESP8266 (1).

How big is a typical board using the SN65HVD232?

The median is 70.8 × 65 mm, and 64% are two-layer designs.

What is the most popular open source board using the SN65HVD232?

By GitHub stars, Bldc by mrkindustries, with 112 stars.

Can I simulate one of these boards using the SN65HVD232 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part