Gatling-V2-board
About the Gatling-V2-board
Gatling-V2-board is an open source NXP PCB design by AREA-Amiens, published on GitHub. It is a 2-layer board measuring 65 × 45 mm, with 28 components from 15 distinct parts.
Its main chip is the TEENSY3.2, from the NXP family. Other key parts include the SN65HVD232 and Pololu_Breakout_DRV8825. By type, the board carries 11 connectors, 6 resistors, 4 diodes, 2 ICs, 2 capacitors and 1 module.
From the project
Hardware for AREA.old boards
Main components on the Gatling-V2-board
Gatling-V2-board bill of materials (BOM)
28 components, 15 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TEENSY3.2 | TEENSY32 | IC1 |
| 1 | SN65HVD232 | SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | Pololu_Breakout_DRV8825 | Pololu_Breakout-16_15.2x20.3mm | A1 |
| 2 | Conn_01x04_Male | Wuerth_2mm_4pin_62000411622 | J1, J4 |
| 2 | Conn_01x02_Male | Wuerth_3.96mm_2pin_645002114822 | J2, J3 |
| 1 | Conn_01x04_Male | PinHeader_1x04_P2.54mm_Horizontal | J5 |
| 6 | Conn_01x03_Male | Wuerth_2.54mm_3pins_61900311121 | J6, J7, J8, J9, J10, J11 |
| 1 | Jumper | PinHeader_1x02_P2.54mm_Vertical | JP1 |
| 1 | SW_DIP_x03 | SW_DIP_SPSTx03_Slide_9.78x9.8mm_W8.61mm_P2.54mm | SW1 |
| 1 | D_TVS_x2_AAC | SOT-23 | D1 |
| 3 | LED | LED_0805_2012Metric | D2, D3, D4 |
| 2 | 100µF | CP_Radial_D8.0mm_P3.50mm | C1, C2 |
| 1 | 120 | R_0603_1608Metric | R1 |
| 2 | 10K | R_0603_1608Metric | R2, R3 |
| 3 | 520 | R_0603_1608Metric | R4, R5, R6 |
Gatling-V2-board design files
The KiCad project lives in the AREA-Amiens/AREA.old-boards-hardware repository on GitHub; these links point at the commit this page was built from.
Gatling-V2-board: common questions
What microcontroller does the Gatling-V2-board use?
The Gatling-V2-board is built around the TEENSY3.2, from the NXP family.
How big is the Gatling-V2-board?
The Gatling-V2-board measures 65 × 45 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Gatling-V2-board?
28 components, from 15 distinct parts. The full bill of materials is listed on this page.
Where can I download the Gatling-V2-board design files?
From the AREA-Amiens/AREA.old-boards-hardware repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Gatling-V2-board design in my own project?
The repository has no license, so all rights stay with AREA-Amiens. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Gatling-V2-board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug NXP firmware against it before you order a PCB.
More boards in AREA.old-boards-hardware
STM32PCB Pompe V2
89.8 × 59.3 mm193 parts2LNo license0
STM32IO Board V1
79 × 49.5 mm88 parts2LNo license0
Carte Alim V4
111.1 × 60 mm57 parts2LNo license0
STM32Sensor v2-board
55.3 × 46 mm47 parts2LNo license0
ESP32PCB ESP32 CAN
52.2 × 67.2 mm47 parts2LNo license0
NXPCarte Principale
80 × 65 mm44 partsNo license0
STM32Rmeasure V1 Board
58 × 28.5 mm43 partsNo license0
NXPAX12 Teensy V1
60 × 41.4 mm20 parts2LNo license0
NXPLidar-V2-board
54.8 × 29 mm15 parts2LNo license0
Similar boards
NXP32Bit shift register
MaltWhiskey
100 × 54 mm56 parts4LNo license763
NXPMega-Cube-Board
200 × 54 mm100 parts4LNo license763
NXPMCL64
MicroCoreLabs
39.3 × 61.8 mm9 parts4LNo license532
NXPROM Emulator
21.5 × 37.1 mm5 parts2LNo license532
NXPMCLZ8
37.1 × 61.5 mm6 parts4LNo license532
NXPXTMAX
81 × 46 mm14 parts4LNo license532