Lidar-V2-board
About the Lidar-V2-board
Lidar-V2-board is an open source NXP PCB design by AREA-Amiens, published on GitHub. It is a 2-layer board measuring 54.8 × 29 mm, with 15 components from 12 distinct parts.
Its main chip is the Teensy3.2, from the NXP family. Other key parts include the SN65HVD232. By type, the board carries 4 connectors, 3 diodes, 3 capacitors, 3 resistors and 2 ICs.
From the project
Hardware for AREA.old boards
Main components on the Lidar-V2-board
Lidar-V2-board bill of materials (BOM)
15 components, 12 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SN65HVD232 | SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | Teensy3.2 | Teensy30_31_32_LC | U2 |
| 1 | Conn_01x05_Female | PinHeader_1x05_P2.54mm_Vertical | J1 |
| 2 | Conn_01x04_Male | JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J2, J3 |
| 1 | Conn_01x02_Male | Molex_KK-396_A-41791-0002_1x02_P3.96mm_Vertical | J4 |
| 2 | LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D2 |
| 1 | SM712_SOT23 | SOT-23 | D3 |
| 1 | 100nF | C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1 |
| 1 | 100µF | CP_Radial_D5.0mm_P2.00mm | C2 |
| 1 | 20µF | CP_Radial_D5.0mm_P2.00mm | C3 |
| 1 | 120 | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1 |
| 2 | 220 | R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R2, R3 |
Lidar-V2-board design files
The KiCad project lives in the AREA-Amiens/AREA.old-boards-hardware repository on GitHub; these links point at the commit this page was built from.
Lidar-V2-board: common questions
What microcontroller does the Lidar-V2-board use?
The Lidar-V2-board is built around the Teensy3.2, from the NXP family.
How big is the Lidar-V2-board?
The Lidar-V2-board measures 54.8 × 29 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Lidar-V2-board?
15 components, from 12 distinct parts. The full bill of materials is listed on this page.
Where can I download the Lidar-V2-board design files?
From the AREA-Amiens/AREA.old-boards-hardware repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Lidar-V2-board design in my own project?
The repository has no license, so all rights stay with AREA-Amiens. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Lidar-V2-board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug NXP firmware against it before you order a PCB.
More boards in AREA.old-boards-hardware
STM32PCB Pompe V2
89.8 × 59.3 mm193 parts2LNo license0
STM32IO Board V1
79 × 49.5 mm88 parts2LNo license0
Carte Alim V4
111.1 × 60 mm57 parts2LNo license0
STM32Sensor v2-board
55.3 × 46 mm47 parts2LNo license0
ESP32PCB ESP32 CAN
52.2 × 67.2 mm47 parts2LNo license0
NXPCarte Principale
80 × 65 mm44 partsNo license0
STM32Rmeasure V1 Board
58 × 28.5 mm43 partsNo license0
NXPGatling-V2-board
65 × 45 mm28 parts2LNo license0
NXPAX12 Teensy V1
60 × 41.4 mm20 parts2LNo license0
Similar boards
NXP32Bit shift register
MaltWhiskey
100 × 54 mm56 parts4LNo license763
NXPMega-Cube-Board
200 × 54 mm100 parts4LNo license763
NXPMCL64
MicroCoreLabs
39.3 × 61.8 mm9 parts4LNo license532
NXPROM Emulator
21.5 × 37.1 mm5 parts2LNo license532
NXPMCLZ8
37.1 × 61.5 mm6 parts4LNo license532
NXPXTMAX
81 × 46 mm14 parts4LNo license532