A3-control center
Axsel·a3-control-center-pcb·hardware/dual_can_esp32.kicad_pcb
About the A3-control center PCB
A3-control center is an open source ESP32 PCB design by Axsel, published on GitHub. It is a 4-layer board measuring 100 × 70 mm, with 109 components from 63 distinct parts.
Its main chip is the ESP32-WROOM-32E-N4, from the ESP32 family. Other key parts include the USBLC6-2SC6, CP2102N-A02-GQFN28R, TPS2553DBVR, TPS62132RGTR and TPS63070RNMR. By type, the board carries 40 resistors, 36 capacitors, 10 ICs, 6 jumpers, 5 connectors and 4 diodes.
From the project
Phase 2 contains a native KiCad 10.0.6 project, a complete hierarchical schematic, a four-layer 100 x 70 mm PCB with all 130 electrical footprints plus four board-only M3 mounting holes functionally placed, JLCPCB-oriented custom design rules, and project-local library tables. US
Phase 2 contains a native KiCad 10.0.6 project, a complete hierarchical schematic, a four-layer 100 x 70 mm PCB with all 130 electrical footprints plus four board-only M3 mounting holes functionally placed, JLCPCB-oriented custom design rules, and project-local library tables. USB data, both converter local power stages, protected USB 5 V and 5V_FT distribution, and the MCP2515 crystal nets are routed over a filled continuous L2 ground plane. The rest of the board is intentionally still in routing development; this is not a manufacturing release.
Main components on the A3-control center
A3-control center bill of materials (BOM)
109 components, 63 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | USBLC6-2SC6 | SOT-23-6 | U1 |
| 1 | CP2102N-A02-GQFN28R Silicon Labs | QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm | U2 |
| 1 | TPS2553DBVR | SOT-23-6 | U3 |
| 1 | TPS62132RGTR | VQFN-16-1EP_3x3mm_P0.5mm_EP1.68x1.68mm_ThermalVias | U4 |
| 1 | TPS63070RNMR | TI_RNM0015A_VQFN-HR-15 | U5 |
| 1 | ESP32-WROOM-32E-N4 | ESP32-WROOM-32E | U10 |
| 1 | TCAN332DR | SOIC-8_3.9x4.9mm_P1.27mm | U20 |
| 1 | MCP2515T-I/SO Microchip | SOIC-18W_7.5x11.6mm_P1.27mm | U40 |
| 1 | TJA1055T/3/2Z NXP | SO-14_3.9x8.65mm_P1.27mm | U41 |
| 1 | THS7314DR Texas Instruments | SOIC-8_3.9x4.9mm_P1.27mm | U60 |
| 2 | SS8050 onsemi | SOT-23 | Q1, Q2 |
| 1 | ABM3BAIG-16.000MHZ-12-2-T Abracon | Crystal_SMD_5032-4Pin_5.0x3.2mm | Y40 |
| 1 | USB4105-GF-A GCT | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | B4B-PH-K-S(LF)(SN) | JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J10 |
| 2 | 1715734 | TerminalBlock_Phoenix_MKDS-1,5-3-5.08_1x03_P5.08mm_Horizontal | J20, J40 |
| 1 | RCJ-014 | RCJ-014 | J60 |
| 1 | CAN_HS TERM ENABLE | SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP20 |
| 1 | CAN_FT RTH ENABLE | SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP40 |
| 1 | CAN_FT RTL ENABLE | SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP41 |
| 1 | BUFFERED DC FIT | SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | JP60 |
Show 43 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | OUTPUT AC DNP | SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP61 |
| 1 | PASSIVE DNP | SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP62 |
| 1 | RESET / EN | SW_Push_1P1T_NO_E-Switch_TL3301NxxxxxG | SW1 |
| 1 | BOOT | SW_Push_1P1T_NO_E-Switch_TL3301NxxxxxG | SW2 |
| 1 | USER | SW_Push_1P1T_NO_E-Switch_TL3301NxxxxxG | SW3 |
| 1 | STATUS GREEN | LED_0603_1608Metric | D10 |
| 2 | PESD2CAN24T-Q | SOT-23 | D20, D40 |
| 1 | HPESD5V0U1BA-Q Nexperia | D_SOD-323 | D60 |
| 1 | 2.2uH WPN4020H2R2MT | WPN4020H | L1 |
| 1 | 1.5uH XGL4020-152MEC | L_Coilcraft_XxL4020 | L2 |
| 1 | 4.7nF 1kV C0G | FV32N472J102EFG | C_1210_3225Metric | C1 |
| 1 | 4.7uF | C_0805_2012Metric | C2 |
| 11 | 100nF | C_0603_1608Metric | C3, C6, C8, C10, C12, C22, C30, C40 +3 |
| 6 | 1uF | C_0805_2012Metric | C4, C20, C31, C41, C46, C62 |
| 1 | 47uF | C_1210_3225Metric | C5 |
| 4 | 10uF | C_0805_2012Metric | C7, C17, C18, C21 |
| 1 | 22uF | C_0805_2012Metric | C9 |
| 1 | 3.3nF | C_0603_1608Metric | C11 |
| 3 | 22uF 16V | C_0805_2012Metric | C13, C14, C15 |
| 2 | 10uF | C_0603_1608Metric | C16, C19 |
| 1 | 100uF low-ESR | C_1210_3225Metric | C23 |
| 2 | 18pF C0G | C_0603_1608Metric | C43, C44 |
| 1 | 100nF X7R FIT | C_0805_2012Metric | C60 |
| 1 | 470uF 6.3V EEEFK0J471GP DNP | CP_Elec_8x10 | C63 |
| 2 | 5.1k 1% | R_0603_1608Metric | R1, R2 |
| 1 | 1M | R_0603_1608Metric | R3 |
| 1 | 0R DNP | R_0603_1608Metric | R4 |
| 1 | 22.1k 1% | R_0603_1608Metric | R5 |
| 1 | 47.5k 1% | R_0603_1608Metric | R6 |
| 2 | 1k | R_0603_1608Metric | R7, R26 |
| 1 | 28.7k 1% | R_0603_1608Metric | R8 |
| 14 | 10k | R_0603_1608Metric | R9, R11, R20, R21, R22, R23, R27, R40 +6 |
| 2 | 100k | R_0603_1608Metric | R10, R14 |
| 1 | 680k 1% | R_0603_1608Metric | R12 |
| 1 | 130k 1% | R_0603_1608Metric | R13 |
| 2 | 4.7k DNP | R_0603_1608Metric | R24, R25 |
| 4 | 0R (CMC bypass) | R_0603_1608Metric | R30, R31, R46, R47 |
| 1 | 120R 1% | R_0603_1608Metric | R32 |
| 2 | 1.2k 1% CONFIG | R_0603_1608Metric | R48, R49 |
| 1 | 33R | R_0603_1608Metric | R60 |
| 1 | 0R DNP (DC INPUT) | R_0603_1608Metric | R61 |
| 1 | 75R 1% | R_0603_1608Metric | R62 |
| 1 | TBD DNP (PASSIVE) | R_0603_1608Metric | R63 |
A3-control center design files
The KiCad project lives in the Axsel/a3-control-center-pcb repository on GitHub; these links point at the commit this page was built from.
A3-control center: common questions
What microcontroller does the A3-control center use?
The A3-control center is built around the ESP32-WROOM-32E-N4, from the ESP32 family.
How big is the A3-control center PCB?
The A3-control center measures 100 × 70 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the A3-control center?
109 components, from 63 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the A3-control center design files?
From the Axsel/a3-control-center-pcb repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the A3-control center design in my own project?
The repository has no license, so all rights stay with Axsel. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the A3-control center without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k