Chiller control

eddyem·stm32samples·F0:F030,F042,F072/Chiller/kicad/Chiller_control.kicad_pcb

Chiller control PCB layout, top view — open source STM32 board by eddyem

About the Chiller control PCB

Chiller control is an open source STM32 PCB design by eddyem, published on GitHub. It is a 2-layer board measuring 62 × 60.5 mm, with 69 components from 44 distinct parts.

Its main chip is the STM32F303CBT6, from the STM32 family. Other key parts include the BME280, ISO1050DUB and 74HC4051. By type, the board carries 26 resistors, 21 capacitors, 7 connectors, 5 transistors, 4 ICs and 2 switches.

It belongs with the sensors designs in this gallery.

From the project

Code samples and ready projects based on bare-metal STM32

UART: 115200N1, not more than 100ms between data bytes in command To turn ON human terminal (without timeout) send "####"

Protocol: [ command line ] '[' clears earlier input '\n', '\r', ' ', '\t' are ignored All messages are asynchroneous!

Commands: Ax - turn on(x=1)/off(x=0) external alarm or check its value Cx - set cooler PWM to x d - (only when EBUG defined) go into debug commands F - get flow sensor rate for 5s period Hx - set heater PWM to x L - check water level sensor value Px - set pump PWM to x R - reset MCU Tx - get NTC temperature for channel x t - get MCU temperature V - get…

Main components on the Chiller control

Chiller control bill of materials (BOM)

69 components, 44 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
BME280
LM1117-3.3
U1
1
STM32F303CBT6
MAX3232
U2
1
ISO1050DUB
STM32F030F4Px
U3
1
74HC4051
L7805
U4
1
B0505S-1W
SI2300
Q1
1
B0509S-1W
SI2300
Q2
1
SI2308
SI2300
Q3
1
B2424S-2W
IRL3303
Q4
1
B0505S-2W
IRL3303
Q5
1
DB9_Female
J1
1
12VIN
J2
2
DC3-10P
J3, J4
1
Cooler
J5
1
Heater
J6
1
Pump
J7
1
Buzzer
BZ1
1
SW_DIP_X01
Reset
SW1
1
SW_DIP_X04
Boot
SW2
1
Val**
hole_3mm
1
SS14
D1
Show 24 more
QtyPartRefs
1
100U
BMBA 0.1mH
L1
3
0.1
C1, C2, C8
9
0.1
C3, C5, C9, C12, C17, C18, C19, C20 +1
1
0.1
47u
C4
1
0.1
1u
C6
1
0.1
10u
C7
2
0.47
C10, C13
1
0.1
0.47
C11
2
1u
C14, C16
1
100u
C15
1
10K
10k
R1
1
4K7
1k0.1%
R2
3
330
1k0.1%
R3, R4, R5
3
330
10k
R6, R8, R9
1
330
220
R7
1
330
510
R10
1
330
220
R11
1
4K7
10k
R12
5
3K3
10k
R13, R14, R15, R19, R20
3
3K3
510
R16, R17, R18
1
560
10k
R21
2
560
220
R22, R26
1
120
220
R23
2
560
0
R24, R25

Chiller control design files

The KiCad project lives in the eddyem/stm32samples repository on GitHub; these links point at the commit this page was built from.

Chiller control: common questions

What microcontroller does the Chiller control use?

The Chiller control is built around the STM32F303CBT6, from the STM32 family.

How big is the Chiller control PCB?

The Chiller control measures 62 × 60.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Chiller control?

69 components, from 44 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Chiller control design files?

From the eddyem/stm32samples repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Chiller control design in my own project?

The repository has no license, so all rights stay with eddyem. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Chiller control without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in stm32samples

Similar boards