Grip strength meter

houseofbigseals·grip_strength_meter_pcb

Grip strength meter PCB layout, top view — open source ESP32 board by houseofbigseals

About the Grip strength meter PCB

Grip strength meter is an open source ESP32 PCB design by houseofbigseals, published on GitHub. It is a 4-layer board measuring 99 × 60 mm, with 97 components from 44 distinct parts.

Its main chip is the ESP32-S2, from the ESP32 family. Other key parts include the W25Q128JVS, CP2102, TP4056, HX711 and TLV75733PDBV. By type, the board carries 39 resistors, 33 capacitors, 8 diodes, 6 ICs, 6 transistors and 3 inductors.

From the project

schematic and pcb for custom esp32 grip strength meter project

Main components on the Grip strength meter

Grip strength meter bill of materials (BOM)

97 components, 44 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
W25Q128JVS
U1
1
CP2102
U2
1
TP4056
U3
1
HX711
U5
1
ESP32-S2
U7
1
TLV75733PDBV
U8
1
SS8550
Q1
2
AO3401A
Q4, Q6
2
MMBT3904
Q5, Q8
1
AO3400A
Q7
1
X252040MMB4SI
Crystal_GND24
Y1
1
Antenna_Chip
AE2
3
H5VL10B
D1, D3, D4
1
RED LED
D7
1
GREEN LED
D8
3
SS54
D9, D11, D12
1
3.3UH
3.3uH
L1
1
2.2NH
2nH
L2
1
2.7NH
2.4nH
L3
15
100NF
100nF
C1, C2, C4, C5, C6, C7, C8, C11 +7
Show 24 more
QtyPartRefs
4
1UF
1uF
C3, C9, C10, C19
5
10UF
10uF
C12, C24, C28, C32, C35
2
10PF
10pF
C15, C16
1
1.2PF
1.2pF
C17
1
1.8PF
1.8pF
C18
2
4.7UF
5uF
C21, C36
2
2.2UF
2uF
C25, C29
1
4.7UF
4.7uF
C27
2
20K
R1, R5
1
8.2K
R2
3
100R
R3, R4, R40
10
C17477
0R
R6, R7, R8, R9, R10, R12, R18, R20 +2
7
10K
R11, R13, R15, R16, R36, R43, R46
2
1K
R14, R23
2
5K1
R17, R19
1
1K5
R26
1
22R
R27
1
499R
R28
1
4K7
R31
1
24K
R33
1
47K
R34
3
100K
R35, R38, R41
2
30K
R37, R42
1
1M
R39

Grip strength meter design files

The KiCad project lives in the houseofbigseals/grip_strength_meter_pcb repository on GitHub; these links point at the commit this page was built from.

Grip strength meter: common questions

What microcontroller does the Grip strength meter use?

The Grip strength meter is built around the ESP32-S2, from the ESP32 family.

How big is the Grip strength meter PCB?

The Grip strength meter measures 99 × 60 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Grip strength meter?

97 components, from 44 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Grip strength meter design files?

From the houseofbigseals/grip_strength_meter_pcb repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Grip strength meter design in my own project?

The repository has no license, so all rights stay with houseofbigseals. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Grip strength meter without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in grip_strength_meter_pcb

Similar boards