SensactInpExt2
klaus-liebler·sensact·pcb/sensactInpExt2/sensactInpExt2.kicad_pcb
About the SensactInpExt2 PCB
SensactInpExt2 is an open source PCB design by klaus-liebler, published on GitHub under the Apache-2.0 license. It is a 2-layer board measuring 90 × 66 mm, with 139 components from 26 distinct parts.
Other key parts include the SRV05-4, PCA9555PW and DS2482. By type, the board carries 64 resistors, 31 switches, 19 capacitors, 8 diodes, 7 jumpers and 6 ICs.
From the project
Es gibt vier Namespaces für Nachrichten "REQUEST" und "RESPONSE", "EVENT" und "ACKNOWLEDGE". Dies wird mit den beiden LSB des Versions-Namespace-Bytes erklärt (Somit bleiben 64 Versionierungsmöglichkeiten) Alle vier Namespaces haben ihren eigenen counter. Dieser beginnt bei 0x0 m
Es gibt vier Namespaces für Nachrichten "REQUEST" und "RESPONSE", "EVENT" und "ACKNOWLEDGE". Dies wird mit den beiden LSB des Versions-Namespace-Bytes erklärt (Somit bleiben 64 Versionierungsmöglichkeiten) Alle vier Namespaces haben ihren eigenen counter. Dieser beginnt bei 0x0 mit der ersten versendeten Nachricht und läuft nach 255 (0xFF) wieder auf 0. Die Ready-Nachricht wird immer mit counter=0x0 übertragen. Sie darf verwendet werden, um die Kommunikations-Session abzubrechen und die counter neu zu starten. Die counter representieren gemeinsames Wissen von Master und Slave REQEST (0b00)…
Main components on the SensactInpExt2
SensactInpExt2 bill of materials (BOM)
139 components, 26 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | SRV05-4 | SOT-23-6 | U1, U3, U4, U6 |
| 1 | PCA9555PW | TSSOP-24_4.4x7.8mm_P0.65mm | U2 |
| 1 | DS2482 | SOIC-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | SensactBusConnector | IDC-Header_2x05_P2.54mm_Horizontal | J1 |
| 1 | IN1-IN8 | PhoenixContact_MC_0,5_8-G-2.5_1x08_P2.50mm_Horizontal | J2 |
| 1 | IN8-IN16 | PhoenixContact_MC_0,5_8-G-2.5_1x08_P2.50mm_Horizontal | J3 |
| 1 | 1WIRE 1Wire | PhoenixContact_MC_1,5_2-G-3.81_1x02_P3.81mm_Horizontal | J4 |
| 1 | SCL | SolderJumper-2_P1.3mm_Bridged2Bar_RoundedPad1.0x1.5mm | JP1 |
| 1 | SDA | SolderJumper-2_P1.3mm_Bridged2Bar_RoundedPad1.0x1.5mm | JP2 |
| 5 | JUMPER_3_OPEN Jumper_3_Open | SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm_NumberLabels | JP3, JP4, JP5, JP6, JP7 |
| 1 | 0 A2 1 | Switch_SS12D00 | SW1 |
| 1 | 0 A1 1 | Switch_SS12D00 | SW2 |
| 1 | 0 A0 1 | Switch_SS12D00 | SW3 |
| 1 | INT0 INT? | Switch_SS12D00 | SW4 |
| 1 | INT2 INT1 | Switch_SS12D00 | SW5 |
| 1 | 0 AD1 1 | Switch_SS12D00 | SW6 |
| 1 | 0 AD0 1 | Switch_SS12D00 | SW7 |
| 8 | C778159 Inp | Button_2x4x3,5 | SW8, SW9, SW10, SW11, SW12, SW13, SW14, SW15 |
| 8 | Inp | Button_2x4x3,5 | SW16, SW17, SW18, SW19, SW20, SW21, SW22, SW23 |
| 8 | SW_Push | SW_SPST_TL3342_smaller | SW24, SW25, SW26, SW27, SW28, SW29, SW30, SW31 |
Show 6 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 8 | LED_Dual_KAKA | Dialight-5530123F-0 | D1, D2, D3, D4, D5, D6, D7, D8 |
| 1 | 10U 10u | C_0603_1608Metric | C1 |
| 18 | C307331 u1 | C_0402_1005Metric | C2, C3, C4, C5, C6, C7, C8, C9 +10 |
| 16 | 10K 10k | R_0402_1005Metric | R1, R2, R3, R4, R7, R10, R11, R14 +8 |
| 16 | 10R | R_0402_1005Metric | R5, R6, R15, R16, R17, R18, R29, R30 +8 |
| 32 | K22 k22 | R_0402_1005Metric | R8, R9, R12, R13, R20, R21, R22, R23 +24 |
SensactInpExt2 design files
The KiCad project lives in the klaus-liebler/sensact repository on GitHub; these links point at the commit this page was built from.
SensactInpExt2: common questions
How big is the SensactInpExt2 PCB?
The SensactInpExt2 measures 90 × 66 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the SensactInpExt2?
139 components, from 26 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the SensactInpExt2 design files?
From the klaus-liebler/sensact repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the SensactInpExt2 design in my own project?
Yes, under the terms of its Apache-2.0 license, which klaus-liebler chose for the repository.
More boards in sensact
ESP32
SensactHs
klaus-liebler
100 × 86.5 mm317 parts2LApache-2.04ESP32
SensactHsIO5
klaus-liebler
90 × 67.5 mm213 parts2LApache-2.04ESP32
SensactHsIO4
klaus-liebler
90 × 74.6 mm196 parts2LApache-2.04ESP32
SensactHsIO3
klaus-liebler
90 × 53 mm187 parts2LApache-2.04ESP32
SensactUp4
klaus-liebler
70 × 70 mm145 parts2LApache-2.04ESP32
SensactOutdoor
klaus-liebler
100 × 91.6 mm129 parts2LApache-2.04ESP32
SensactHsNano2
klaus-liebler
90 × 56.5 mm128 parts2LApache-2.04ESP32
SensactHsNano3
klaus-liebler
90 × 56 mm122 parts2LApache-2.04ESP32
SensactHsLed2 - Kopie
klaus-liebler
90 × 47.5 mm117 parts2LApache-2.04ESP32
SensactHsLed2
klaus-liebler
90 × 74.7 mm116 parts2LApache-2.04ESP32
SensactHs modular esp32
klaus-liebler
100 × 86.5 mm25 parts2LApache-2.04