SensactHs modular esp32
klaus-liebler·sensact·pcb/sensactHs_modular_esp32/sensactHs_modular_esp32.kicad_pcb
About the SensactHs modular esp32 PCB
SensactHs modular esp32 is an open source ESP32 PCB design by klaus-liebler, published on GitHub under the Apache-2.0 license. It is a 2-layer board measuring 100 × 86.5 mm, with 25 components from 19 distinct parts.
Its main chip is the ESP32-S3-DEVKITC, from the ESP32 family. Other key parts include the SN65HVD230, MODULE_TPA3110, MODULE_PCM5102, DCDC_MP2315 and AMS1117. By type, the board carries 6 ICs, 5 connectors, 5 capacitors, 4 resistors, 1 module and 1 switch.
It belongs with the iot & wireless designs in this gallery.
From the project
Es gibt vier Namespaces für Nachrichten "REQUEST" und "RESPONSE", "EVENT" und "ACKNOWLEDGE". Dies wird mit den beiden LSB des Versions-Namespace-Bytes erklärt (Somit bleiben 64 Versionierungsmöglichkeiten) Alle vier Namespaces haben ihren eigenen counter. Dieser beginnt bei 0x0 m
Es gibt vier Namespaces für Nachrichten "REQUEST" und "RESPONSE", "EVENT" und "ACKNOWLEDGE". Dies wird mit den beiden LSB des Versions-Namespace-Bytes erklärt (Somit bleiben 64 Versionierungsmöglichkeiten) Alle vier Namespaces haben ihren eigenen counter. Dieser beginnt bei 0x0 mit der ersten versendeten Nachricht und läuft nach 255 (0xFF) wieder auf 0. Die Ready-Nachricht wird immer mit counter=0x0 übertragen. Sie darf verwendet werden, um die Kommunikations-Session abzubrechen und die counter neu zu starten. Die counter representieren gemeinsames Wissen von Master und Slave REQEST (0b00)…
Main components on the SensactHs modular esp32
SensactHs modular esp32 bill of materials (BOM)
25 components, 19 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-DEVKITC ESP32-S3-DevKitC | AIthinker_ESP32_S3 | U1 |
| 1 | SN65HVD230 | SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | MODULE_TPA3110 | TPA3110_module | U3 |
| 1 | MODULE_PCM5102 | MODULE_PCM5102A | U4 |
| 1 | DCDC_MP2315 | MODULE_STEPDOWN | U5 |
| 1 | AMS1117 | SOT-223-3_TabPin2_HANDSOLDER | U6 |
| 1 | W5500_MINI W5500_mini | W5500-mini | M1 |
| 1 | SensactBusConnector | IDC-Header_2x05_P2.54mm_Horizontal | J1 |
| 2 | CAN | PhoenixContact_MC_1,5_5-G-3.81_1x05_P3.81mm_Horizontal | J2, J3 |
| 1 | Speaker | PhoenixContact_MC_1,5_5-G-3.81_1x05_P3.81mm_Horizontal | J4 |
| 1 | 24V | PhoenixContact_MC_1,5_2-G-3.5_1x02_P3.50mm_Horizontal | J5 |
| 1 | VOL RIGHT | Potentiometer_Alps_RK09K_Single_Vertical | RV1 |
| 1 | VOL LEFT | Potentiometer_Alps_RK09K_Single_Vertical | RV2 |
| 1 | TERM ON | Switch_SS12D00 | SW1 |
| 1 | NUP2105 | SOT-23_Handsoldering | D1 |
| 3 | u1 | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C3, C4 |
| 2 | 22U 22u | C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C2, C5 |
| 3 | 4K7 4k7 | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R3, R4 |
| 1 | K12 | R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R2 |
SensactHs modular esp32 design files
The KiCad project lives in the klaus-liebler/sensact repository on GitHub; these links point at the commit this page was built from.
SensactHs modular esp32: common questions
What microcontroller does the SensactHs modular esp32 use?
The SensactHs modular esp32 is built around the ESP32-S3-DEVKITC, from the ESP32 family.
How big is the SensactHs modular esp32 PCB?
The SensactHs modular esp32 measures 100 × 86.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the SensactHs modular esp32?
25 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the SensactHs modular esp32 design files?
From the klaus-liebler/sensact repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the SensactHs modular esp32 design in my own project?
Yes, under the terms of its Apache-2.0 license, which klaus-liebler chose for the repository.
Can I test firmware for the SensactHs modular esp32 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in sensact
ESP32
SensactHs
klaus-liebler
100 × 86.5 mm317 parts2LApache-2.04ESP32
SensactHsIO5
klaus-liebler
90 × 67.5 mm213 parts2LApache-2.04ESP32
SensactHsIO4
klaus-liebler
90 × 74.6 mm196 parts2LApache-2.04ESP32
SensactHsIO3
klaus-liebler
90 × 53 mm187 parts2LApache-2.04ESP32
SensactUp4
klaus-liebler
70 × 70 mm145 parts2LApache-2.04SensactInpExt2
klaus-liebler
90 × 66 mm139 parts2LApache-2.04ESP32
SensactOutdoor
klaus-liebler
100 × 91.6 mm129 parts2LApache-2.04ESP32
SensactHsNano2
klaus-liebler
90 × 56.5 mm128 parts2LApache-2.04ESP32
SensactHsNano3
klaus-liebler
90 × 56 mm122 parts2LApache-2.04ESP32
SensactHsLed2 - Kopie
klaus-liebler
90 × 47.5 mm117 parts2LApache-2.04ESP32
SensactHsLed2
klaus-liebler
90 × 74.7 mm116 parts2LApache-2.04
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k