HardLabs

Flip0pocket s

LordRobertShaw·flip0pocket-s·hardware/kicad/pocket-s.kicad_pcb

Flip0pocket s PCB layout, top view — open source ESP32 board by LordRobertShaw

About the Flip0pocket s PCB

Flip0pocket s is an open source ESP32 PCB design by LordRobertShaw, published on GitHub. It is a 4-layer board measuring 85 × 52 mm, with 28 components from 28 distinct parts.

Its main chip is the ESP32-S3-WROOM-1-N8R8, from the ESP32 family. Other key parts include the CC1101RGPR, PN5180A0ET/C110F, TP4056, TPS62740DSST and USB_C_Receptacle. By type, the board carries 7 ICs, 7 switches, 3 crystals, 2 transistors, 2 connectors and 2 LEDs.

It belongs with the iot & wireless, rf & radio and power & battery designs in this gallery.

From the project

A fully open-source, modular multi-tool platform built on ESP32-S3. Sub-1GHz RF • NFC • 125kHz RFID • IR • BLE • WiFi • Expandable Modules

A fully open-source, modular multi-tool platform built on ESP32-S3. Sub-1GHz RF • NFC • 125kHz RFID • IR • BLE • WiFi • Expandable Modules

Getting Started • Hardware • Firmware • KiCad • Docs • Contributing

MCU: ESP32-S3-WROOM-1 (Dual-core LX7 @ 240MHz, 8MB Flash, 8MB PSRAM) Display: 1.54" IPS LCD, 240×240, ST7789V Battery: 3.7V 1200mAh LiPo, USB-C charging Dimensions: 85 × 55 × 12 mm

Main components on the Flip0pocket s

ESP32-S3-WROOM-1-N8R8CC1101RGPRPN5180A0ET/C110FTP4056TPS62740DSSTUSB_C_ReceptacleMicroSD_Card

Flip0pocket s bill of materials (BOM)

28 components, 28 distinct parts.

QtyPartRefs
1
ESP32-S3-WROOM-1-N8R8
Espressif
U1
1
CC1101RGPR
Texas Instruments
U2
1
PN5180A0ET/C110F
PN5180A0ET
NXP
U3
1
TP4056
U5
1
TPS62740DSST
U6
1
USB_C_Receptacle
U8
1
MicroSD_Card
U9
1
BSS138
Q1
1
TSOP38238
Q2
1
32MHz
Y1
1
32.768kHz
Y2
1
26MHz
Y4
1
Expansion_20pin
J1
1
SWD_Debug
J2
1
Piezo_85dB
LS1
1
BTN_UP
SW1
1
BTN_DOWN
SW2
1
BTN_LEFT
SW3
1
BTN_RIGHT
SW4
1
BTN_OK
SW5
Show 8 more
QtyPartRefs
1
BTN_BACK
SW6
1
RESET
SW7
1
Red
LED1
1
Green
LED2
1
WS2812B
D1
1
100nF
C1
1
10uF
C2
1
10k
R1

Flip0pocket s design files

The KiCad project lives in the LordRobertShaw/flip0pocket-s repository on GitHub; these links point at the commit this page was built from.

Flip0pocket s: common questions

What microcontroller does the Flip0pocket s use?

The Flip0pocket s is built around the ESP32-S3-WROOM-1-N8R8, from the ESP32 family.

How big is the Flip0pocket s PCB?

The Flip0pocket s measures 85 × 52 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Flip0pocket s?

28 components, from 28 distinct parts. The full bill of materials is listed on this page.

Where can I download the Flip0pocket s design files?

From the LordRobertShaw/flip0pocket-s repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the Flip0pocket s design in my own project?

The repository has no license, so all rights stay with LordRobertShaw. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Flip0pocket s without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards