Atlas dock charger
md-sazzad-eee·ATLAS·02_electronics/dock_charger/atlas_dock_charger.kicad_pcb
About the Atlas dock charger PCB
Atlas dock charger is an open source PCB design by md-sazzad-eee, published on GitHub. It is a 2-layer board measuring 90 × 66 mm, with 119 components from 36 distinct parts.
Other key parts include the LMV358, TPS54202DDC, INA180A2, MCP4725A0T-E/CH and 74LVC1G08. By type, the board carries 48 resistors, 33 capacitors, 15 ICs, 11 diodes, 5 transistors and 4 connectors.
It belongs with the power & battery, robotics & motion and sensors designs in this gallery.
From the project
Modular multi-robot system: a carrier robot that docks, transports, charges and redeploys two small agent robots. KiCad, FreeCAD, MATLAB/Simulink, COMSOL and ESP32 firmware.
KiCad 10 project: agentcontroller/atlasagentctrl.kicadpro Design source of truth: agentcontroller/design/boardbdesign.py`, which holds every part, value, footprint and pin→net assignment.
- Power in: 2S Li-ion (J1, with NTC), then a 3 A PTC, then a reverse-polarity P-MOSFET (AOD409), then a TVS (SMBJ10CA) and 100 µF bulk. - Dock charge path: J2 pads (VCHG, GND, DATA, ID), then an SS34 diode (no backfeed to the pads), then the charge switch Q2, which the ESP32 can open (CHGEN). - The ID resistor R8 sets agent identity: 10 k for S1, 22 k for S2. - DATA is a half-duplex UART with 1 k series…
Main components on the Atlas dock charger
Atlas dock charger bill of materials (BOM)
119 components, 36 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LMV358 | SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 2 | TPS54202DDC | SOT-23-6 | U101, U201 |
| 2 | INA180A2 | SOT-23-5 | U102, U202 |
| 2 | MCP4725A0T-E/CH | SOT-23-6 | U103, U203 |
| 2 | 74LVC1G08 | SOT-23-5 | U104, U204 |
| 2 | INA226 (I, V) | MSOP-10_3x3mm_P0.5mm | U105, U205 |
| 2 | INA226 (VCHG contact) | MSOP-10_3x3mm_P0.5mm | U106, U206 |
| 2 | INA226 (GND contact) | MSOP-10_3x3mm_P0.5mm | U107, U207 |
| 1 | AOD409 (rev-pol) | TO-252-2 | Q1 |
| 2 | AO3401A | SOT-23 | Q101, Q201 |
| 2 | 2N7002 | SOT-23 | Q102, Q202 |
| 1 | VIN 4S (+,-) | AMASS_XT30PW-M_1x02_P2.50mm_Horizontal | J1 |
| 1 | BAY 1 DOCK (VF,VS,GF,GS,DATA,ID) | JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J2 |
| 1 | BAY 2 DOCK (VF,VS,GF,GS,DATA,ID) | JST_XH_B6B-XH-A_1x06_P2.50mm_Vertical | J3 |
| 1 | TO BOARD A | PinHeader_2x08_P2.54mm_Vertical | J4 |
| 1 | 3A hold PTC | Fuse_1812_4532Metric | F1 |
| 1 | SMBJ16CA | D_SMB | D1 |
| 2 | BAT54J | D_SOD-323 | D101, D201 |
| 2 | AMBER charging | LED_0603_1608Metric | D102, D202 |
| 2 | SMAJ12CA | D_SMA | D103, D203 |
Show 16 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | PESD5V0S1BL | D_SOD-323 | D104, D105, D204, D205 |
| 2 | 22uH 2.5A | L_Bourns_SRR1260 | L101, L201 |
| 1 | 100uF 25V | CP_Elec_8x10 | C1 |
| 1 | 10uF | C_0805_2012Metric | C2 |
| 23 | 100nF | C_0603_1608Metric | C3, C102, C103, C106, C107, C108, C110, C111 +15 |
| 2 | 10uF 25V | C_1206_3216Metric | C101, C201 |
| 4 | 22uF 25V | C_1206_3216Metric | C104, C105, C204, C205 |
| 2 | 1uF | C_0603_1608Metric | C109, C209 |
| 2 | 2.2k | R_0603_1608Metric | R1, R2 |
| 2 | 130k 0.1% | R_0603_1608Metric | R101, R201 |
| 2 | 10.0k 0.1% | R_0603_1608Metric | R102, R202 |
| 10 | 100k | R_0603_1608Metric | R103, R109, R111, R114, R115, R203, R209, R211 +2 |
| 2 | 20m 1% | R_1206_3216Metric | R104, R204 |
| 16 | 10k | R_0603_1608Metric | R105, R106, R107, R108, R110, R112, R118, R119 +8 |
| 6 | 1k | R_0603_1608Metric | R113, R116, R117, R213, R216, R217 |
| 8 | 10R | R_0603_1608Metric | R120, R121, R122, R123, R220, R221, R222, R223 |
Atlas dock charger design files
The KiCad project lives in the md-sazzad-eee/ATLAS repository on GitHub; these links point at the commit this page was built from.
Atlas dock charger: common questions
How big is the Atlas dock charger PCB?
The Atlas dock charger measures 90 × 66 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Atlas dock charger?
119 components, from 36 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Atlas dock charger design files?
From the md-sazzad-eee/ATLAS repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Atlas dock charger design in my own project?
The repository has no license, so all rights stay with md-sazzad-eee. Use it as a reference, and ask the author before reusing the design.
More boards in ATLAS
Similar boards
Sensor smd
scottbez1
40 × 20 mm5 parts2LApache-2.04.2kSensors
StuckAtPrototype
15.2 × 9 mm14 parts4LApache-2.03.8kEinkPDA screen
TalismanDesign
95 × 54 mm27 parts2LApache-2.02.0kStack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kDisplay Carrier
AxxAxx
35.6 × 58.2 mm5 parts2LGPL-3.01.7kMicrophone
Mentra-Community
5.5 × 6.1 mm6 parts2LMIT1.2k