28 open source boards using the MCP4725A0T-E/CH
Real designs built with the MCP4725A0T-E/CH, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Cellsim-8ch
atopile
13 × 9 mm608 parts4LMIT29ML1
brucemack
125 × 56 mm64 parts2LGPL-3.018BatteryAnalyzer MkII
Moragor
101.6 × 53.3 mm25 parts2LMIT12ESP32
UPLC-Analog
fredriknk
31.4 × 22 mm48 parts4LMIT4EEG
MariusFauteux
110 × 85 mm370 parts4LNo license1STM32
Flyback-Driver
Operationorange01
128 × 72.5 mm115 parts4LNo license1ESP32
Pd brick
enkhbold470
100 × 80 mm116 parts4LCERN-OHL-S-2.00ESP32
Pd brick
enkhbold470
100 × 80 mm116 parts4LCERN-OHL-S-2.00Camera-Cooler
lukaslibar
45 × 75 mm106 parts4LCustom license0AVR/Arduino
Custom PSU
GodOfStrategy
99.6 × 73.1 mm105 parts2LNo license0ESP32
IDM-RoomSensor-ESP-B-ES4-AIR-R2
Xerolux
130 × 100 mm102 parts4LCERN-OHL-S-2.00STM32
Nylok-Heater
3nboyd
38 × 100 mm64 parts2LNo license0STM32
Nylok-Heater
boydportfolio
38 × 100 mm64 parts2LNo license0ESP32
D03-MAIN-CTRL
byhabibi
160 × 115 mm59 parts2LNo license0AVR/Arduino
Mie1001 daq board
Chaospossum
68.6 × 53.3 mm38 parts2LNo license0ML2
brucemack
125 × 56 mm64 parts2LGPL-3.018Atlas dock charger
md-sazzad-eee
90 × 66 mm119 parts2LNo license0ESP32
IDM-RoomSensor-ESP-B-ES5-MODULAR
Xerolux
130 × 100 mm84 parts4LCERN-OHL-S-2.00ML3
brucemack
130 × 56 mm63 parts2LGPL-3.018ESP32
IDM-RoomSensor-ESP-B-ES3-C6
Xerolux
130 × 80 mm80 parts4LCERN-OHL-S-2.00ML4
brucemack
130 × 56 mm63 parts2LGPL-3.018ESP32
IDM-RoomSensor-ESP-B-ES2-C6
Xerolux
110 × 70 mm52 parts4LCERN-OHL-S-2.00ML0
brucemack
100 × 59 mm60 parts2LGPL-3.018AVR/Arduino
IDM-RoomSensor-Classic-B-ES1
Xerolux
145 × 78 mm22 parts2LCERN-OHL-S-2.00Cell
atopile
95.1 × 8.4 mm64 parts4LMIT29ESP32
IDM-RoomSensor-ESP-B-ES1
Xerolux
145 × 78 mm20 parts2LCERN-OHL-S-2.00ESP32
IDM-FakeSensor-ESP-B-ES1
Xerolux
145 × 78 mm18 parts2LCERN-OHL-S-2.00Analog out
atopile
16 × 5 mm8 parts2LMIT29
How designs wire the MCP4725A0T-E/CH
Read from the KiCad layouts of 16 open source designs, one per repository: what each pin of the MCP4725A0T-E/CH connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 12 of 16 designs, most often 4.7 kΩ (then 10 kΩ).
- The SCL pin has a pull-up to 3.3V on 12 of 16 designs, most often 4.7 kΩ (then 10 kΩ).
- The VOUT pin has a series resistor on 10 of 16 designs, most often 4.7 kΩ (then 10 kΩ).
- The A0 pin is tied to GND on 11 of 14 designs (a signal on 3).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VOUTpin 1 | Connected to: Signal 100% |
|
| VSSpin 2 | Connected to: GND 94% | — |
| VDDpin 3 | Connected to: 3.3V 75% · a signal 19% |
|
| SDApin 4 | Connected to: The microcontroller 50%, a connector 25% |
|
| SCLpin 5 | Connected to: The microcontroller 38% |
|
| A0pin 6 | Connected to: GND 79% · a signal 21% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Analog out by atopile, ML0 by brucemack, BatteryAnalyzer MkII by Moragor and UPLC-Analog by fredriknk.
The MCP4725A0T-E/CH in open source designs
The gallery holds 28 open source boards using the MCP4725A0T-E/CH from 16 GitHub repositories; a typical one measures about 105.8 × 72.8 mm and carries around 64 components.
57% are two-layer designs, the rest use four layers or more, and 68% carry an open source license.
The most starred is Cellsim-8ch by atopile.
Parts used alongside the MCP4725A0T-E/CH
Microcontrollers on boards using the MCP4725A0T-E/CH
What boards using the MCP4725A0T-E/CH are built for
MCP4725A0T-E/CH: common questions
Where can I find a MCP4725A0T-E/CH reference design?
Each of the 28 boards on this page is a real design using the MCP4725A0T-E/CH. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the MCP4725A0T-E/CH SDA pin?
The SDA pin has a pull-up to 3.3V on 12 of 16 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 16 open source designs using the MCP4725A0T-E/CH.
What pull-up resistor is used on the MCP4725A0T-E/CH SCL pin?
The SCL pin has a pull-up to 3.3V on 12 of 16 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 16 open source designs using the MCP4725A0T-E/CH.
What resistor goes on the MCP4725A0T-E/CH VOUT pin?
The VOUT pin has a series resistor on 10 of 16 designs, most often 4.7 kΩ (then 10 kΩ). Counted from the KiCad layouts of 16 open source designs using the MCP4725A0T-E/CH.
What parts are used alongside the MCP4725A0T-E/CH?
The ADS1115IDGSR, AP63203WU-7, AP7381-33Y-13, ESP32-S3-WROOM-1-N8R8 and INA180A2IDBVR appear in the most repositories here.
Which microcontrollers do boards using the MCP4725A0T-E/CH use?
Most are built on ESP32 (10), AVR/Arduino (3) and STM32 (3).
How big is a typical board using the MCP4725A0T-E/CH?
The median is 105.8 × 72.8 mm, and 57% are two-layer designs.
What is the most popular open source board using the MCP4725A0T-E/CH?
By GitHub stars, Cellsim-8ch by atopile, with 29 stars.
Can I simulate one of these boards using the MCP4725A0T-E/CH before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.