Atlas carrier ctrl
md-sazzad-eee·ATLAS·02_electronics/carrier_controller/atlas_carrier_ctrl.kicad_pcb
About the Atlas carrier ctrl PCB
Atlas carrier ctrl is an open source ESP32 PCB design by md-sazzad-eee, published on GitHub. It is a 4-layer board measuring 130 × 100 mm, with 145 components from 63 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N8, from the ESP32 family. Other key parts include the TPS54302, AP2112K-3.3, USBLC6-2SC6, TPS3823-33DBV and 74LVC1G00. By type, the board carries 50 resistors, 40 capacitors, 19 connectors, 18 ICs, 7 diodes and 6 transistors.
It belongs with the robotics & motion, power & battery and sensors designs in this gallery.
From the project
Modular multi-robot system: a carrier robot that docks, transports, charges and redeploys two small agent robots. KiCad, FreeCAD, MATLAB/Simulink, COMSOL and ESP32 firmware.
KiCad 10 project: agentcontroller/atlasagentctrl.kicadpro Design source of truth: agentcontroller/design/boardbdesign.py`, which holds every part, value, footprint and pin→net assignment.
- Power in: 2S Li-ion (J1, with NTC), then a 3 A PTC, then a reverse-polarity P-MOSFET (AOD409), then a TVS (SMBJ10CA) and 100 µF bulk. - Dock charge path: J2 pads (VCHG, GND, DATA, ID), then an SS34 diode (no backfeed to the pads), then the charge switch Q2, which the ESP32 can open (CHGEN). - The ID resistor R8 sets agent identity: 10 k for S1, 22 k for S2. - DATA is a half-duplex UART with 1 k series…
Main components on the Atlas carrier ctrl
Atlas carrier ctrl bill of materials (BOM)
145 components, 63 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TPS54302 | SOT-23-6 | U1 |
| 1 | AP2112K-3.3 | SOT-23-5 | U2 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U3 |
| 1 | ESP32-S3-WROOM-1-N8 | ESP32-S3-WROOM-1 | U4 |
| 1 | TPS3823-33DBV | SOT-23-5 | U5 |
| 2 | 74LVC1G00 | SOT-23-5 | U6, U7 |
| 2 | 74LVC1G11 | SOT-23-6 | U8, U9 |
| 1 | TCA9534PWR | TSSOP-16_4.4x5mm_P0.65mm | U10 |
| 4 | INA180A1 | SOT-23-5 | U11, U12, U13, U14 |
| 4 | DRV8871DDA | Texas_HTSOP-8-1EP_3.9x4.9mm_P1.27mm_EP2.95x4.9mm_Mask2.4x3.1mm_ThermalVias | U15, U16, U17, U18 |
| 1 | AOD409 (rev-pol) | TO-252-2 | Q1 |
| 1 | 2N7002 | SOT-23 | Q2 |
| 1 | AOD409 (motor rail) | TO-252-2 | Q3 |
| 3 | AO3400A | SOT-23 | Q4, Q5, Q6 |
| 1 | BATT 4S (+,-) | AMASS_XT60PW-M_1x02_P7.20mm_Horizontal | J1 |
| 1 | SBC POWER OUT (VBAT,GND) | AMASS_XT30PW-M_1x02_P2.50mm_Horizontal | J2 |
| 1 | BOARD C POWER (VBAT,GND) | AMASS_XT30PW-M_1x02_P2.50mm_Horizontal | J3 |
| 1 | USB-C (ROS 2 link) | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J4 |
| 1 | E-STOP (NC) | JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J5 |
| 1 | BAY 1 SENSORS (GND,SEATED,LATCHED_N) | JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J6 |
Show 43 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | BAY 2 SENSORS (GND,SEATED,LATCHED_N) | JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J7 |
| 1 | LATCH 1 SOLENOID (12V) | JST_VH_B2P-VH_1x02_P3.96mm_Vertical | J8 |
| 1 | LATCH 2 SOLENOID (12V) | JST_VH_B2P-VH_1x02_P3.96mm_Vertical | J9 |
| 1 | QWIIC I2C (IMU) | JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | J10 |
| 1 | TO BOARD C | PinHeader_2x08_P2.54mm_Vertical | J11 |
| 1 | MOTOR LF | JST_VH_B2P-VH_1x02_P3.96mm_Vertical | J12 |
| 1 | MOTOR LR | JST_VH_B2P-VH_1x02_P3.96mm_Vertical | J13 |
| 1 | MOTOR RF | JST_VH_B2P-VH_1x02_P3.96mm_Vertical | J14 |
| 1 | MOTOR RR | JST_VH_B2P-VH_1x02_P3.96mm_Vertical | J15 |
| 1 | ENCODER LF | JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J16 |
| 1 | ENCODER LR | JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J17 |
| 1 | ENCODER RF | JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J18 |
| 1 | ENCODER RR | JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J19 |
| 1 | 5V magnetic buzzer | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | 15A mini blade | Fuseholder_Blade_Mini_Keystone_3568 | F1 |
| 1 | RESET | SW_SPST_TL3342 | SW1 |
| 1 | BOOT | SW_SPST_TL3342 | SW2 |
| 1 | SMBJ16CA | D_SMB | D1 |
| 2 | SS14 | D_SMA | D2, D3 |
| 1 | RED motors armed | LED_0603_1608Metric | D4 |
| 2 | SS34 flyback | D_SMA | D5, D6 |
| 1 | GREEN status | LED_0603_1608Metric | D7 |
| 1 | 10uH 4A | L_Bourns_SRR1260 | L1 |
| 1 | 470uF 25V | CP_Elec_10x10.5 | C1 |
| 26 | 100nF | C_0603_1608Metric | C2, C5, C6, C12, C14, C15, C16, C17 +18 |
| 2 | 10uF 25V | C_1206_3216Metric | C3, C4 |
| 2 | 22uF 10V | C_1206_3216Metric | C7, C8 |
| 2 | 1uF | C_0603_1608Metric | C9, C13 |
| 2 | 10uF | C_0805_2012Metric | C10, C11 |
| 1 | 220uF 25V | CP_Elec_8x10 | C19 |
| 4 | 47uF 25V | CP_Elec_6.3x7.7 | C31, C35, C39, C43 |
| 10 | 100k | R_0603_1608Metric | R1, R3, R12, R13, R14, R22, R24, R29 +2 |
| 1 | 18k | R_0603_1608Metric | R2 |
| 1 | 20k | R_0603_1608Metric | R4 |
| 1 | 75k 1% | R_0603_1608Metric | R5 |
| 1 | 10k 1% | R_0603_1608Metric | R6 |
| 2 | 5.1k | R_0603_1608Metric | R7, R8 |
| 16 | 10k | R_0603_1608Metric | R9, R10, R11, R16, R17, R18, R19, R25 +8 |
| 6 | 1k | R_0603_1608Metric | R15, R28, R41, R51, R61, R71 |
| 2 | 100 | R_0603_1608Metric | R21, R23 |
| 2 | 4.7k | R_0603_1608Metric | R26, R27 |
| 4 | 20m 1% | R_1206_3216Metric | R40, R50, R60, R70 |
| 4 | 22k (2.9A trip) | R_0603_1608Metric | R42, R52, R62, R72 |
Atlas carrier ctrl design files
The KiCad project lives in the md-sazzad-eee/ATLAS repository on GitHub; these links point at the commit this page was built from.
Atlas carrier ctrl: common questions
What microcontroller does the Atlas carrier ctrl use?
The Atlas carrier ctrl is built around the ESP32-S3-WROOM-1-N8, from the ESP32 family.
How big is the Atlas carrier ctrl PCB?
The Atlas carrier ctrl measures 130 × 100 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Atlas carrier ctrl?
145 components, from 63 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Atlas carrier ctrl design files?
From the md-sazzad-eee/ATLAS repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Atlas carrier ctrl design in my own project?
The repository has no license, so all rights stay with md-sazzad-eee. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Atlas carrier ctrl without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in ATLAS
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k