Atlas agent ctrl
md-sazzad-eee·ATLAS·02_electronics/agent_controller/atlas_agent_ctrl.kicad_pcb
About the Atlas agent ctrl PCB
Atlas agent ctrl is an open source ESP32 PCB design by md-sazzad-eee, published on GitHub. It is a 2-layer board measuring 110 × 90 mm, with 100 components from 48 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N8R8, from the ESP32 family. Other key parts include the TPS563201, AP2112K-3.3, USBLC6-2SC6, TPS3823-33DBV and 74LVC1G08. By type, the board carries 37 resistors, 26 capacitors, 10 ICs, 9 connectors, 7 transistors and 7 diodes.
It belongs with the robotics & motion, power & battery and sensors designs in this gallery.
From the project
Modular multi-robot system: a carrier robot that docks, transports, charges and redeploys two small agent robots. KiCad, FreeCAD, MATLAB/Simulink, COMSOL and ESP32 firmware.
KiCad 10 project: agentcontroller/atlasagentctrl.kicadpro Design source of truth: agentcontroller/design/boardbdesign.py`, which holds every part, value, footprint and pin→net assignment.
- Power in: 2S Li-ion (J1, with NTC), then a 3 A PTC, then a reverse-polarity P-MOSFET (AOD409), then a TVS (SMBJ10CA) and 100 µF bulk. - Dock charge path: J2 pads (VCHG, GND, DATA, ID), then an SS34 diode (no backfeed to the pads), then the charge switch Q2, which the ESP32 can open (CHGEN). - The ID resistor R8 sets agent identity: 10 k for S1, 22 k for S2. - DATA is a half-duplex UART with 1 k series…
Main components on the Atlas agent ctrl
Atlas agent ctrl bill of materials (BOM)
100 components, 48 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TPS563201 | SOT-23-6 | U1 |
| 1 | AP2112K-3.3 | SOT-23-5 | U2 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U3 |
| 1 | ESP32-S3-WROOM-1-N8R8 | ESP32-S3-WROOM-1 | U4 |
| 1 | TPS3823-33DBV | SOT-23-5 | U5 |
| 1 | 74LVC1G08 | SOT-23-5 | U6 |
| 2 | INA180A2 | SOT-23-5 | U7, U8 |
| 2 | DRV8871DDA | Texas_HTSOP-8-1EP_3.9x4.9mm_P1.27mm_EP2.95x4.9mm_Mask2.4x3.1mm_ThermalVias | U9, U10 |
| 1 | AOD409 (rev-pol) | TO-252-2 | Q1 |
| 1 | AO3401A (charge sw) | SOT-23 | Q2 |
| 3 | 2N7002 | SOT-23 | Q3, Q4, Q7 |
| 1 | AOD409 (motor cut) | TO-252-2 | Q5 |
| 1 | AO3401A (Pi power) | SOT-23 | Q6 |
| 1 | BATT 2S (+,-,NTC) | JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J1 |
| 1 | DOCK PADS (VCHG,GND,DATA,ID) | JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J2 |
| 1 | USB-C (program/debug) | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J3 |
| 1 | MOTOR+ENC L | JST_PH_B6B-PH-K_1x06_P2.00mm_Vertical | J4 |
| 1 | MOTOR+ENC R | JST_PH_B6B-PH-K_1x06_P2.00mm_Vertical | J5 |
| 1 | PI ZERO 2W (5V,5V,GND,GND,TX,RX) | JST_GH_SM06B-GHS-TB_1x06-1MP_P1.25mm_Horizontal | J6 |
| 1 | QWIIC I2C (GND,3V3,SDA,SCL) | JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | J7 |
Show 28 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SENSOR MODULE | JST_GH_SM08B-GHS-TB_1x08-1MP_P1.25mm_Horizontal | J8 |
| 1 | DEBUG UART0 | PinHeader_1x04_P2.54mm_Vertical | J9 |
| 1 | 3A hold PTC | Fuse_1812_4532Metric | F1 |
| 1 | RESET | SW_SPST_TL3342 | SW1 |
| 1 | BOOT | SW_SPST_TL3342 | SW2 |
| 1 | SMBJ10CA | D_SMB | D1 |
| 1 | SS34 (no backfeed) | D_SMA | D2 |
| 1 | PESD3V3S1BL | D_SOD-323 | D3 |
| 2 | SS14 | D_SMA | D4, D5 |
| 1 | GREEN status | LED_0603_1608Metric | D6 |
| 1 | RED 3V3 | LED_0603_1608Metric | D7 |
| 1 | 2.2uH 4A (SRN6045TA-2R2) | L_Bourns_SRN6045TA | L1 |
| 2 | 100uF 16V | CP_Elec_6.3x7.7 | C1, C18 |
| 12 | 100nF | C_0603_1608Metric | C2, C3, C4, C7, C14, C16, C17, C20 +4 |
| 4 | 10uF 25V | C_0805_2012Metric | C5, C6, C19, C21 |
| 2 | 22uF 10V | C_0805_2012Metric | C8, C9 |
| 3 | 1uF | C_0603_1608Metric | C10, C12, C15 |
| 2 | 10uF | C_0805_2012Metric | C11, C13 |
| 1 | 220uF 10V | CP_Elec_6.3x7.7 | C26 |
| 10 | 100k | R_0603_1608Metric | R1, R4, R5, R6, R12, R19, R20, R21 +2 |
| 2 | 22k | R_0603_1608Metric | R2, R7 |
| 10 | 10k | R_0603_1608Metric | R3, R8, R11, R14, R17, R18, R28, R29 +2 |
| 6 | 1k | R_0603_1608Metric | R9, R10, R26, R27, R36, R37 |
| 1 | 56k | R_0603_1608Metric | R13 |
| 2 | 5.1k | R_0603_1608Metric | R15, R16 |
| 2 | 20m 1206 | R_1206_3216Metric | R22, R23 |
| 2 | 33k (2.0A trip) | R_0603_1608Metric | R24, R25 |
| 2 | 4.7k | R_0603_1608Metric | R34, R35 |
Atlas agent ctrl design files
The KiCad project lives in the md-sazzad-eee/ATLAS repository on GitHub; these links point at the commit this page was built from.
Atlas agent ctrl: common questions
What microcontroller does the Atlas agent ctrl use?
The Atlas agent ctrl is built around the ESP32-S3-WROOM-1-N8R8, from the ESP32 family.
How big is the Atlas agent ctrl PCB?
The Atlas agent ctrl measures 110 × 90 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Atlas agent ctrl?
100 components, from 48 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Atlas agent ctrl design files?
From the md-sazzad-eee/ATLAS repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Atlas agent ctrl design in my own project?
The repository has no license, so all rights stay with md-sazzad-eee. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Atlas agent ctrl without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in ATLAS
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k